Products

Mass Air Flow Sensor - TDCi is the intake air mass sensor for the TDCi diesel engine, forming part of the air intake assembly. Fitted in the intak...

Spill Rail for the 300 TDi fuel injection system. The spill rail links the leak-off unions at the top of the injectors and carries surplus fuel fro...

Nylon Washer for the interior and exterior mirror mountings. The washer sits between the mirror arm or bracket and its mounting face, spacing the ...

Washer is a nylon door hinge washer used on the hinge fixing bolts. It fits over the hinge bolt as a low-friction spacer between the moving hinge ...

Captive Nut with a UNF thread, providing a fixed threaded anchor point for a bolted fixing. The nut is retained in its bracket or panel so it cann...

Door Hinge Bolt - countersunk UNF type - within the door assembly. This countersunk fixing bolt secures the door hinge plate to the door face, com...

Sill Panel - right-hand rear - within the lower body structure on Double Cab variants. This pressed steel panel fits along the lower edge of the r...

Sill Panel - Rear - LH for the Defender 110 in standard and double cab body configurations. This outer steel sill panel forms the lower rear body ...

Rear Wing - nearside (left-hand) rear bodyside outer panel. Part of the exterior body structure, forming the outer skin of the rear body side above...

Wing Fixing Plate is a three-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (fro...

Wing Fixing Plate is a two-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (front...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Washer is a large plain flat washer used as a general-purpose load-spreading fastening component, sized for M6 fixings with a wider outside diamete...

Spare Wheel Buffer for a bonnet-mounted spare wheel. This moulded rubber buffer fits to the bonnet panel and bears against the back of the spare wh...

Door Bottom Seal for the front door. This rubber seal fits along the lower edge of the door, closing the gap between the door bottom and the body t...

Door Seal - Bottom for the left-hand front door, forming part of the door-aperture weather sealing. The seal fits along the lower edge of the door...

Bonnet Buffer is a resilient rubber cushion that forms part of the bonnet closure assembly at the front of the body. It provides the stop the bonn...

Quarter Panel Valance - RH for the Defender 110 Station Wagon. This pressed steel valance panel forms the lower rear section of the right-hand rea...

Bonnet Prop Clip for the bonnet support rod assembly on the Land Rover Defender. This clip secures the solid-type bonnet prop rod in its stowed po...

Heater Blower Duct Seal for diesel applications, fitted in the heater air intake. This foam seal sits between the air inlet duct and the heater blo...

Heater Blower Duct Seal for diesel applications, fitted in the heater air intake. This foam seal sits between the air inlet duct and the heater blo...

Overcentre Catch - a spring-loaded toggle latch used to secure hinged covers, lids and access panels. When the lever is thrown past its centre poi...

Wheelarch Eyebrow is the front wheelarch eyebrow moulding, part of the front wheelarch trim assembly. It mounts to the upper section of the front ...

Stud used in the rear body upper fixings. The stud provides the threaded shank at the upper mounting points where the rear body ties into the vehi...

Heater Blower Seal sealing the joint between the intake grille and the heater duct, for diesel applications. Fitted in the heater air intake, it cl...

Fuel Injector for the Td5 2.5L 5-cylinder turbo diesel engine. The Td5 uses electronic unit injectors, one per cylinder, seated in the cylinder hea...

Fuel Injector - fuel injection system, cylinder head. Td5 2.5L 5-cylinder turbo diesel. The Td5 uses electronic unit injectors: each injector sits...

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder diesel engine, sealing the fuel connector block to the engine within the fuel pressure r...

Blanking Plug Grommet for the dash assembly. This rubber plug fills an unused aperture in the dash panel - such as the opening for the hand throttl...

Radiator Grille Panel forming the central front fascia of the Land Rover Defender body. This panel fits the nose section of the vehicle, housing t...

Mudflap Stiffener Bracket for the front mudflap assembly. The bracket mounts behind the front mudflap to hold it rigid and maintain its shape, pre...

Soft Top Drain Channel Spring for the soft top header rail and drain channel assembly. The spring tensions the soft top against the header rail, h...

Aluminium Decal - 15cm nameplate for the exterior body. This aluminium nameplate measures 15cm in length and is applied to the exterior body as a ...

Bracket Fixing used at the steering column top support. The steering column top support carries the upper end of the column against the facia stru...

Soft Top Drain Channel runs along the right-hand side of the soft top, directing rainwater run-off from the canopy away from the body sides.

Soft Top Drain Channel runs along the left-hand side of the soft top, directing rainwater run-off from the canopy away from the body sides.

Sun Visor is the pivoting padded screen at the top of the windscreen aperture, hinged from the header rail to shield the occupant from glare and sw...

Heater Fan Decal - the printed label applied to the heater control panel on the facia, identifying the blower fan control. Restores the original m...