Products

Brake Pipe – Rear Drum – Right is a pre-formed rigid pipe serving the right-hand rear drum brake. It carries hydraulic pressure to the rear drum a...

Fuel Pipe forming part of the fuel supply circuit on carburettor petrol engines. It carries fuel along the delivery run between the fuel pump and ...

Track Rod End - Cross Rod Eye is the ball-jointed eye end of the steering cross rod, in the steering linkage. It screws into the end of the cross ...

Plate - Power Steering Pipes is the retaining plate in the power steering pipe assembly. It clamps the steering pipe run at its mounting point, ho...

Hand Throttle Cable is the secondary throttle control cable, operated by a hand control rather than the accelerator pedal. It holds the throttle l...

Oil Cooler Pipe carries engine oil between the engine and the oil cooler, forming part of the lubrication cooling circuit. It routes pressurised o...

Coupling Assembly - union fitting for the engine oil cooler pipe circuit. This union connects adjacent oil cooler pipe sections in the engine bay,...

Brake Master Cylinder 110/130 Non-ABS

Rear Silencer Pipe forms the rearmost section of the exhaust system, combining the rear silencer (muffler) with an integral tailpipe. It installs ...

Dump Valve

Front Exhaust Downpipe for the 2.25L 4-cylinder diesel engine. The downpipe is the first section of the exhaust system. It bolts to the exhaust ma...

Fitment: 90/110 to 1998 Not TD5

Fitment:  2.5D &amp: 2.5TD

Wing Nut for the air cleaner assembly. This threaded wing nut secures the air cleaner cover to its centre stud, clamping the cover down to retain ...

Front Right-Hand Brake Pipe for the hydraulic braking circuit, non-ABS systems. This pre-formed rigid steel pipe carries brake fluid through the f...

Front Left-Hand Brake Pipe for the hydraulic braking circuit, non-ABS systems. This pre-formed rigid steel pipe carries brake fluid through the fr...

Fuel Filler Cap for the fuel tank filler neck - pressed metal, three-lug bayonet fitting, non-locking and non-vented. The cap seals the filler nec...

Brake Master Cylinder is the primary hydraulic actuator of the braking circuit, converting pedal effort transmitted through the brake servo into th...

Fuel Filler Cap for the fuel tank filler neck - pressed metal, two-lug bayonet fitting, non-locking and vented. The cap seals the filler neck agai...

Mounting Bolt for the fuel tank pump and mounting assembly. It secures the fuel pump and its mounting bracket at the tank mounting point in the fu...

Crankshaft Position Sensor for the Td5 2.5L 5-cylinder turbo diesel engine management system. The sensor reads the toothed reluctor on the flywheel...

Crankshaft Position Sensor for the Td5 2.5L 5-cylinder turbo diesel engine management system. The sensor reads the toothed reluctor on the flywheel...

M12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

Exhaust Downpipe, Right-Hand is the front section of the exhaust system on the 3.5L V8 petrol in non-catalyst configuration. It bolts to the right...

Pipe Clip for retaining and routing rigid hydraulic pipework against the chassis and body panels. Used on brake pipe runs with drum brakes and no ...

Brake Pipe Clip - Double - a moulded plastic clip that secures two brake pipes to the chassis within the braking hydraulic circuit. It retains bot...

Exhaust U-Bolt secures the exhaust system at its mounting points, clamping the pipe to a bracket or holding adjacent sections of the exhaust line t...

bracket exhaust OEM - 90" 4-cyl N/A diesel and 90" 4-cyl petrol (except MPI)

Bracket exhaust - 90" 4-cylinder petrol (Except MPI) and 2.5 NA

Choke Cable assembly for carburettor-fed 2.25L and 2.5L four-cylinder petrol engines, right-hand drive applications. The cable links the dashboard...

Choke Cable operates the carburettor choke from the driver's control within the fuel and cold-start system, for the 2.5L 4-cylinder petrol carburet...

Fuel Tank Plug, M12 threaded, fitted to the fuel tank body. It seals a threaded port in the tank associated with the fuel pump, sender and filler ...

Fuel Pick-Up and Return Pipe Assembly for the fuel tank on diesel applications using the metal fuel tank. The pick-up pipe draws fuel from inside ...

Intermediate Exhaust Pipe for the 2.5L petrol engine, connecting the front downpipe to the centre silencer in the Defender exhaust system. Pipe le...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...