Products

Rocker Shaft Assembly forms part of the valvetrain (rocker gear) on the overhead-valve V8 petrol engine. Mounted on pedestals above the cylinder h...

Oil Pump Gear for the 3.5L V8 engine oil pump, part of the lubrication system. The oil pump draws oil from the sump and pressurises it for deliver...

Tensioner Pulley Bearing for the auxiliary drive belt system on air-conditioned vehicles. It is the bearing carried within the idler/tensioner pul...

Distributor Gear

Bolt securing the exhaust manifold on the Rover V8 petrol engine. A 3/8" UNC x 1 1/8" fastener used to retain the exhaust manifold to the cylinder...

Idler Pulley for the auxiliary (ancillary) drive belt of the air-conditioning system. The pulley guides and tensions the belt that drives the air-...

Brake Disc - Solid - Rear is the rear brake disc, mounting to the rear hub and providing the friction surface the brake pads clamp against during b...

Engine Dowel, a precision locating dowel that sets the relative position of mating engine components during assembly. The dowel fixes the exact al...

Grommet

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Nut — a threaded fastener that pairs with a bolt or stud to clamp components together. It is run onto the matching thread and tightened to secure ...

Brake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...

Piston for the 3.5L V8 petrol engine, standard (nominal) bore size. It reciprocates within the cylinder bore, transmitting combustion pressure thr...

Piston for the 3.5L Rover V8 petrol engine, supplied at +0.020" oversize with an 8.13:1 compression ratio. The +0.020" oversize suits a rebored bl...

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Oil Pump Relief Plunger is the pressure-relief valve plunger within the engine oil pump, part of the lubrication system on the 3.5L V8 petrol engin...

Speedo drive oil seal LT230

Sedimentor Seal for the diesel fuel sedimentor assembly. The sedimentor separates water and sediment from the fuel ahead of the injection system. ...

Sedimentor Sealing Ring for the diesel fuel filter and sedimentor assembly. The sedimentor separates water and sediment from the diesel fuel befor...

Self-Tapping Screw - a No. 8 x 3/8" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as it ...

Self Tapping Screw for use in Land Rover body, chassis, and hardware applications.

Tap screw

Screen Washer Pump for the rear window wash circuit. This electric pump draws washer fluid from the reservoir and delivers it under pressure to th...

Suppressor Capacitor mounted at the ignition coil as part of the ignition system. It suppresses the radio-frequency interference generated by the ...

Camshaft Bearing Kit

Brake Caliper Seal Repair Kit the seal set for resealing a four-piston brake caliper within the hydraulic braking system. This kit contains the pi...

Clutch master cylinder

Brake Caliper is the front right-hand hydraulic caliper in the front disc brake assembly. It houses the pistons that press the brake pads against ...

Brake Caliper is the front left-hand hydraulic caliper in the front disc brake assembly. It houses the pistons that press the brake pads against t...

Diesel Fuel Filter - replaceable cartridge filter element for the fuel supply circuit on 200 TDi and 300 TDi diesel engines. The element sits in t...

Vacuum Pump Rotor Blade for the engine-driven brake servo vacuum pump. The blade runs within the rotor of the vacuum pump, generating the vacuum t...

Handbrake Expander Assembly for the drum-type transmission (parking) brake mounted at the rear output of the transfer box. The expander sits betwe...

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

Joint Washer - a sealing washer for the piston-cooling oil squirt jet in the engine lubrication circuit. It seals the oil spray jet where it meets...

Vent Panel Stud Bolt for the dashboard air vent panel assembly on Land Rover Defender without air conditioning. This stud bolt secures the dash ve...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Extension Valance is a lower body panel that closes off the wheelarch and valance section of the bodywork. It bolts to the existing valance struct...

Extension Valance is a lower body panel that closes off the wheelarch and valance section of the bodywork. It bolts to the existing valance struct...

Bonnet Release Cable forms the mechanical link in the bonnet latch and release system, transmitting the pull from the cabin-mounted release lever t...

Channel glass front door. - Discovery1 from (VIN) MA137190 onwards, - RRclassic 4-door from (VIN) MA659911 onwards. Also fits Discovery2 front LH ...

Rear Floor Crossmember, a transverse structural member beneath the rear load floor. This crossmember runs across the underside of the body and sup...

Glazing Rubber Seal for the front door drop glass lift channel on the Discovery 1 and Range Rover Classic. This rubber strip seats inside the wind...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...