Products

Layshaft Bearing for the LT77 and R380 5-speed manual gearbox fitted to the Defender, Discovery 1, Discovery 2, and Range Rover P38. The layshaft ...

Layshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...

Oil Cooler Pipe - a rigid pipe in the automatic transmission's oil cooling circuit, carrying fluid between the gearbox and the transmission oil coo...

Gearbox Spring - the synchroniser spring for the 1st and 2nd gear synchroniser assembly within the five-speed manual gearbox. It maintains tension...

Shift Plate

Mainshaft Spacer - a spacer fitted to the gearbox mainshaft of the five-speed manual gearbox. It sets the axial position of the gears and bearings...

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Clutch Driven Plate (235mm) transmits engine torque from the flywheel to the gearbox input shaft within the clutch assembly. The friction plate sp...

Clutch Cover is the pressure plate assembly of the clutch, bolting to the engine flywheel within the clutch and gearbox coupling. Its diaphragm sp...

Lock Nut for the front output shaft, used in the transfer box assembly. This nut secures the front output shaft drive flange within the transfer b...

Drive Shaft Housing Bolt securing the drive shaft (swivel/stub axle) housing to the axle case. An M10 double-hex (twelve-point) headed bolt used a...

Intermediate shaft lock nut LT230

Plug

Plain Washer with a 6 mm (1/4") bore, a general-purpose flat washer for use with M6 fasteners. Fitted beneath a bolt head or nut to spread the cla...

Washer 20mm

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Plain Washer - Swivel Pin Housing is a flat washer used within the front axle swivel pin housing assembly. It seats beneath the housing fixing bolt...

Wheel Bearing Kit - Front and Rear

Wheel Bearing Kit - Front and Rear

Plain Washer in M6 oversize form, with a larger outer diameter than a standard M6 washer. It spreads the clamping load of a bolt head or nut over ...

Plain Washer - flat washer for use in general fastening assemblies throughout the vehicle. Distributes load and protects mating surfaces under bol...

Washer - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...

Serrated Washer, 7/16", used within the clutch master cylinder and pipe assembly. The serrated face bites into the mating surface as the fixing is...

Repair Washer - M10 for use in suspension, axle and body fastening applications. A large-diameter flat washer that distributes the clamping load o...

Spring Washer for use as a locking fastener component across Land Rover assemblies. A helical split spring washer providing resistance against fas...

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Spring Washer - M10 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to...

Spring Washer for use across a wide range of fixings and assembly applications on Land Rover vehicles. This split-ring spring washer is placed ben...

Spring Washer is a split spring lock washer fitted under a nut or bolt head to maintain clamping tension and resist loosening caused by vibration. ...

Plain Washer - flat steel washer from the hardware and fixings group. It is fitted under a bolt head or nut to spread the clamp load over the join...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Kit gasket carb for Rover V8 engines fitted with SU carburetors

Handbrake Disc - transmission-mounted brake disc, the rotating element of the disc-type transmission handbrake conversion. Mounts on the transfer ...

Handbrake Pad Set - replacement friction pads for the X-Eng disc handbrake (transmission brake) conversion. The conversion replaces the drum-type ...

High Note Horn, the high-pitched unit of the vehicle's dual-tone horn system. It sounds together with the low note horn to produce the two-tone au...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

High Note Horn - the higher-pitched element of the dual-tone warning horn assembly. Mounted behind the front grille or valance and paired with a l...

Alternator – 300TDi The engine-driven charging unit that powers the electrical system and maintains battery charge on the 2.5L 300 Tdi diesel engin...

Fuse - 60A - high-current blade fuse for the main electrical protection circuits. Rated at 60 amps, this fuse protects high-draw circuits such as ...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Flasher Unit, an electronic direction-indicator flasher relay for towing applications. It regulates the flash rate of the direction indicators and...

Alarm Remote Transmitter, the handset used for remote operation of the vehicle's anti-theft alarm and central locking system. The unit transmits a...