Products

Brake Pad Set - replacement friction pads for the front disc brake calipers, supplied as a complete axle set. The pads locate in the caliper carri...

Brake Disc - front brake discs supplied as a pair, one for each side of the front axle. The disc mounts to the front hub and forms the friction su...

Cargo Liner - shaped loadspace floor liner for the Discovery 1 rear load area. The liner drops into the loadspace and covers the original floor co...

Oil Pump Gear Set - replacement gear set for the crankshaft-driven oil pump in the Rover V8 petrol engine lubrication system. The gears run in the...

Air Locker - air-operated selectable locking differential for the Salisbury rear axle with 24-spline halfshafts. Replaces the standard differentia...

RR Spring Front Heavy Duty - Discovery Defender

RR Spring Rear Heavy Duty - Discovery

Front Coil Spring - front suspension coil spring, seated between the axle spring pad and the chassis spring turret to support the vehicle and contr...

Heavy Duty spring Range Rover rear +0mm

Enhance the performance and handling of your Defender 110 with this rear coil spring pair. Designed for heavy-duty use, these yellow springs are pe...

Air locker - a pneumatically operated differential lock that replaces the standard differential centre in a Rover-type axle running 24-spline halfs...

Rubber floor mat set for the front footwells. Moulded in rubber and shaped to the driver and passenger floor pan, the mats lay over the original c...

Rubber Floor Mat Set - Rear, part of the interior floor trim. Covers the rear footwell area. The mats lay over the existing floor covering and tak...

Rear Brake Pad Set - friction pads for the rear disc brake assembly. The pads sit in the caliper on either side of the brake disc. When the hydrau...

Auto Transmission Service Kit - service kit for the ZF four-speed automatic gearbox, covering the internal oil filter and its sealing components. ...

Rear Body Mount secures the rear body tub to the rear chassis crossmember, maintaining body-to-chassis alignment and damping vibration. Steel, sup...

Body Mounting Kit renews the body-to-chassis mounting points, where the body is located and secured to the chassis frame. The rubber mounts isolat...

Front Lowering Coil Spring for the front coil-sprung suspension. Fitted in place of the standard front coil spring, seating between the chassis sp...

Silicone Coolant Hose Kit is a set of silicone hoses for the cooling system expansion tank bleed circuit. Silicone construction withstands higher ...

Coolant header tank in aluminium, forming the expansion and filling point of the engine cooling circuit. The tank absorbs the change in coolant vo...

Front Brake Pad Set - friction pads for the front disc brake calipers, forming part of the front foundation braking assembly. The pads are carried...

Brake Pad Set - rear axle, part of the rear disc brake assembly. The pads are clamped against the rear brake disc by the caliper pistons and handl...

On-Board Air Load-Assist System (Load Controller II) – the air supply and control circuit for rear air helper springs. The system feeds both rear ...

Gaiter Retrim Kit - a three-piece set of replacement lever gaiters for the centre console. The kit re-covers the three transmission-tunnel levers ...

Radius Arm Pair - 3 Degree Caster Correction for the front suspension radius arm assembly on coil-sprung Land Rovers fitted with a 25-75 mm (1-3 in...

Rear Radius Arm locates the axle and controls its fore-and-aft movement, with geometry set for a 2 inch suspension lift. The revised arm restores ...

Handbrake Conversion Kit - converts the drum-type transmission brake to a disc and caliper arrangement on the rear output of the LT230 transfer box...

Steering Arm Fixing Kit for the heavy-duty steering arms DA5503 and DA5504. It supplies the fixings needed to mount the heavy-duty steering arms i...

Clutch Kit for the 200 TDi and 300 TDi diesel engines, uprated to a heavy-duty specification. The clutch transmits drive from the engine to the ge...

Clutch Kit HD 200/300 TDi

Clutch Kit for the 200 TDi and 300 TDi diesel engines, uprated to a heavy-duty specification. The clutch transmits drive from the engine to the ge...

Front Steel Winch Bumper with a black protective finish, replacing the standard front bumper to add front-end protection and an integral winch moun...

HD Rear Bumper

CV Joint Kit for the front axle swivel housing assembly. The constant velocity joint sits at the outer end of the front axle shaft, inside the swiv...

CV Joint Kit for the front axle swivel housing assembly. The constant velocity joint sits at the outer end of the front axle shaft, inside the swiv...

CV Joint Kit for the front axle swivel housing assembly. The constant velocity joint sits at the outer end of the front axle shaft, inside the swiv...

Front Shock Absorber Turret: the tubular mounting tower that locates the upper end of the front damper. It bolts to the chassis and provides the t...

Turret Securing Ring for the front shock absorber turret, supplied as a pair. The rings clamp the turret to its mounting in the front suspension. ...

Propshaft Spacer Kit for the driveline, fitting between the differential drive flange and the propeller shaft to add 15 mm of length. When a suspe...

Propshaft Spacer Kit (25mm) - a driveline spacer fitted between the propshaft flange and the transfer box or differential flange to restore the pro...

Double Cardan Front Propshaft Kit - a heavy-duty front propshaft for the LT230 transfer box, using a double cardan (constant-velocity) joint at the...

Protective Coating Kit - Tintable (4 L) for applying a durable, textured surface coating to body panels, underbody areas, wheel arches, load beds, ...

Coating Spray Gun, bottle-mount type, for applying protective coating. This Schutz-style gun screws directly onto the 750ml coating bottle, so no s...

Alloy Wheel, 18 x 8 with ET20 offset and a 5 x 165.1 mm (five-stud) bolt pattern, finished in black. The wheel forms the mounting interface betwee...

Alloy Wheel - road wheel measuring 18 inch diameter by 8J rim width, with an ET20 offset and a 5 x 165 mm PCD stud pattern, finished in silver. Th...

Alloy Wheel - road wheel measuring 16 inch diameter by 7J rim width, with an ET20 offset and a 5 x 165 mm PCD stud pattern. Gloss black finish with...