Products

Washer used with the rear bumper moulding fixings. Spreads clamping load at the moulding fastening on the rear bumper assembly.

Rear Wheel Arch Moulding Washer for the Discovery 3 (L319) and Discovery 4 (L319). This washer is used in the fixing arrangement that secures the ...

Nut - Plastic - 7mm is a captive plastic fastener for trim and body panel fixing. This plastic nut presses into a 7mm hole in the body or trim pan...

Nut - Plastic - 7mm is a captive plastic fastener for trim and body panel fixing. This plastic nut presses into a 7mm hole in the body or trim pan...

Fitment: 2005 - 2009

Head Gasket Kit (Less Head Gasket) - a cylinder head gasket and seal set for the 2.7L Lion V6 turbo diesel engine, supplied without the cylinder he...

Con Rod Bearing Set - a complete set of connecting rod (big-end) bearing shells for the 2.7L Lion V6 turbo diesel engine. The shells locate betwee...

Con Rod Bearing Set - a set of connecting rod (big-end) bearing shells for the 2.7L Lion V6 turbo diesel engine, supplied in the 010 undersize. Th...

Main Bearing Set - a complete set of crankshaft main bearing shells for the 2.7L Lion V6 turbo diesel engine. The shells locate between the cranks...

Main Bearing Set - a set of crankshaft main bearing shells for the 2.7L Lion V6 turbo diesel engine, supplied in the 010 undersize. The shells loc...

Main Bearing Set for the crankshaft of the 2.7L V6 diesel engine, supplied at 0.020 in undersize. The main bearings are the plain shell bearings t...

Main Bearing Set for the crankshaft of the 2.7L V6 diesel engine, supplied at 0.030 in undersize. The main bearings are the plain shell bearings t...

Outlet Water Tube

Sunroof Water Drain Tube for the power tilt-and-slide sunroof drainage system. It routes water collected in the sunroof cassette drain channel down...

Clip - Side D Pillar Upper Discovery 3 Discovery 4 RS1 RS2

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flanged Hex Bolt, M12 x 70mm. Secures the front wheel hub assembly to the steering knuckle (upright) within the front suspension and hub assembly....

Bolt - a threaded fastener used within the axle and suspension assembly. It secures front axle case mountings and rear suspension arm attachments,...

Bolt - a threaded fastener used within the rear axle and suspension assembly. It secures the rear knuckle and suspension arm mountings, clamping e...

Bonnet Safety Catch for the bonnet (hood) latch system, the secondary catch that retains the bonnet after the primary latch is released. It holds ...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Flanged Head Screw, M8 x 12 mm. A metric set screw with an integral flange beneath the hexagon head that spreads clamping load and helps resist loo...

Screw - threaded fastener used in vehicle assembly.

Fuel Filler Flap Actuator for the fuel filler flap locking mechanism. The actuator drives the fuel filler flap between its locked and released pos...

Anti-Roll Bar Bolt - a chassis fixing bolt in the suspension system, securing the anti-roll (stabiliser) bar to the vehicle structure. It clamps t...

Screw - a general fixing screw used at several mounting points across the driveline and body, including transmission and transfer case mountings, t...

Hex Nut - M12 flanged nut. Used in the front suspension, securing the anti-roll bar clamp and drop link fixings and suspension arm fasteners. The ...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Hex Nut - M14 for use in Land Rover suspension and general fastener applications. A metric M14 standard hexagonal nut for use in axle, suspension,...

Fuel Filler Flap Latch Repair Kit - replacement latch hardware for the fuel filler flap assembly in the rear quarter panel. The flap is held close...

Piston, standard size, for the 3.0L TDV6 turbo diesel engine. Part of the cylinder block assembly – crankshaft, connecting rods and pistons. The p...

Gearbox Sump Pan Kit for the ZF 6HP26 and 6HP28 six-speed automatic transmission - converts the transmission from its original one-piece sump with ...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...