Products

Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...

Thermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...

Camshaft Screw for the cylinder head and camshaft assembly of the 3.0-litre TDV6 diesel engine. This is a manufacturer-specification retaining scr...

Manifold Absolute Pressure (MAP) Sensor for the 3.0L V6 diesel engine. Mounted on the throttle housing, it measures the absolute pressure in the i...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Oil Filter Housing Cover is the cover for the cartridge-type oil filter assembly on 3.0 GDI petrol and 5.0 AJ-V8 engines. This cover retains the r...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

EGR Gasket Inlet

EGR Tube connecting the exhaust manifold to the EGR valve on the 3.0L V6 turbo diesel engine. Carries hot exhaust gas from the exhaust manifold to...

EGR Tube connecting the exhaust manifold to the EGR valve on the 3.0L V6 turbo diesel engine. Carries hot exhaust gas from the exhaust manifold to...

Fuel Return Pipe for the diesel fuel system return circuit, 3.0L V6 diesel applications. The return pipe carries surplus fuel not consumed by the ...

Automatic Transmission Fluid (ATF) for the automatic gearbox and power steering circuit. Specified as the transmission and power steering fluid to...

Output Shaft Oil Seal for the ZF 8HP eight-speed automatic transmission. Seals the transmission output shaft where it exits the gearbox housing, p...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Cylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...

Plastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...

Trim Clip - a plastic push-fit retaining clip used to secure exterior trim and body mouldings to the vehicle. It locates in a pre-drilled panel hol...

Lamp - Side Flasher

Lamp - Side Flasher

Oil Cooler Tube forms part of the engine oil cooling circuit, carrying oil between the engine and the oil cooler. Used on 5.0L V8 and 3.0L V6 supe...

Body Moulding Retainer Clip, a lantern-type fastener for the vehicle's exterior trim. The clip secures exterior body mouldings - such as the rocke...

Sealing Ring seals the joint between the engine oil cooler and the water pump on the AJ133 5.0L V8 and 3.0L supercharged V6 petrol engines. It mai...

Chain - Timing

Auxiliary Drive Chain for the AJ133 5.0L V8 and 3.0L V6 supercharged petrol engines. It forms part of the engine's chain drive assembly, running a...

Leak-Off Tube - Injection Pump

Fuel Injector Sealing Washer for diesel injector installations. The washer seals the fuel injector against its seat in the cylinder head, containi...

Wiper Arm Cap - a trim cover for the windscreen wiper arm spindle. Conceals and protects the wiper arm retaining nut at the base of the front wipe...

Retaining Clip - a push-fit fastener used to secure exterior and interior trim mouldings and finishers to the body. The clip pushes into a locatin...

Differential Mounting Washer - fitted at the front differential mounting to spread the clamp load across the housing insulator bush. The washer se...

Differential Mounting Washer - fitted at the front differential mounting to spread the clamp load across the housing insulator bush. The washer se...

Ride Height Sensor - electronic air suspension height sensor. The sensor links the suspension arm to the body and continuously reports the ride he...

Ride Height Sensor - rear electronic air suspension height sensor. The sensor links the rear suspension arm to the body and continuously reports t...

Bush - front crossmember and stabiliser bar mounting insulator within the front suspension assembly. The insulator locates the front crossmember a...

Bush - front axle case mounting insulator within the front suspension assembly. The insulator isolates the front axle case from the body, absorbin...

Brake Caliper Mounting Bolt for the front brake assembly, securing the caliper to its mounting on the hub carrier. This high-tensile fastener is t...

Brake Pad Wear Warning Wire for the rear brake pads, part of the brake pad wear warning circuit. The sensor wire is routed at the rear brake pad a...

Steering Column Joint of double cruciform (universal joint) design, fitted in the steering column intermediate shaft. It transmits steering input ...

EGR Cooler Hose for the exhaust gas recirculation (EGR) circuit on the 3.0L 24V DOHC V6 turbo diesel engine. It carries engine coolant to the EGR ...

Water Outlet Tube carries coolant between the water pump and the thermostat housing within the engine cooling circuit. For 3.0L supercharged V6 an...

Exhaust Manifold Bolt secures the exhaust manifold to the cylinder head. For 3.0L supercharged V6 and 5.0L V8 petrol applications.

Flanged Nut for the front suspension arm mountings. The integral flange spreads the clamp load across the joint face and helps the nut resist loos...

Flanged Nut for use in Land Rover assembly applications. The integrated flange acts as a built-in load-spreading face, distributing clamping force ...