for Discounts / VAT
for Discounts & Correct VAT
O-Ring for the turbocharger of the 2.0L I4 diesel (AJ200) engine, sealing the upper turbocharger-to-pipe joint (14.3 x 2.4 mm). The O-ring seals t...
View full detailsO-Ring sealing a turbocharger oil and coolant connection within the turbocharger lubrication and cooling circuit. It seals the union at the turboc...
View full detailsWater Outlet Tube forming the coolant outlet connection at the cylinder head, part of the engine cooling circuit. It carries coolant from the cyli...
View full detailsBolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...
View full detailsExhaust Manifold Gasket sealing the exhaust manifold and turbocharger joint. The same gasket serves both the exhaust manifold and the turbocharger...
View full detailsIdler Pulley for the accessory drive belt system, 65 mm in diameter. It guides the accessory (auxiliary) drive belt across its run, maintaining be...
View full detailsCamshaft Sprocket for the timing drive of the Ingenium engine family - the 2.0L and 3.0L diesel and 3.0L petrol units. Mounted on the end of the ca...
View full detailsSpecial Bolt for the engine timing gear assembly. It secures a component within the timing gear drive. Fitted to 2.0-litre diesel Ingenium engines...
View full detailsTiming Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...
View full detailsTiming Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...
View full detailsTiming Chain Tensioner Arm for the engine timing gear. It bears against the timing chain and transmits the tensioner load to take up slack and mai...
View full detailsCamshaft Sprocket for the camshaft drive, mounted on the end of the camshaft and driven by the timing chain from the crankshaft. It transmits the d...
View full detailsFuel Pump Drive Sprocket for the 2.0L Ingenium diesel engine (AJ200 / AJ20D4). The sprocket drives the high-pressure fuel pump from the engine's ti...
View full detailsValve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...
View full detailsSealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...
View full detailsCover Gasket for the upper timing chain cover. It seals the joint between the upper timing chain cover and the engine, maintaining an oil-tight se...
View full detailsSeal for the oil filter to oil cooler connection, part of the oil cooler and filter assembly. This O-ring seals the joint between the oil filter h...
View full detailsIntake Manifold Gasket seals the joint between the intake manifold and the cylinder head, within the air intake assembly. It maintains an airtight...
View full detailsExhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head, within the exhaust assembly. It contains combustion ga...
View full detailsManifold Absolute Pressure (MAP) Sensor for the 3.0L V6 diesel engine, mounted in the throttle housing. It measures absolute pressure in the intake...
View full detailsPower Seat Adjust Switch - the switch pack controlling powered front seat adjustment. Mounted on the seat, it operates the electric front seat adj...
View full detailsCoolant Hose – Radiator to Engine Vent Elbow connects the radiator to the engine vent elbow, within the cooling system pipes and hoses. It carries...
View full detailsExhaust Clamp secures a joint between two sections of the exhaust system, clamping the adjoining pipes together to form a gas-tight connection whil...
View full detailsAdhesive and Sealer is a glass bonding adhesive and sealer used to seat and seal fixed automotive glazing to the body. It bonds and seals the wind...
View full detailsThrottle Body and Motor in the engine air intake system, supplied with an integral electric actuator motor. On this 3.0L V6 diesel, the throttle b...
View full detailsFront Door Latch - the left-hand (driver side) door latch assembly, mounted in the shut face of the front door. It engages the striker on the body...
View full detailsValve Spring Seat is the seat on the cylinder head that locates the base of the valve spring, providing the surface against which the spring is com...
View full detailsTiming Belt
EGR Outlet Gasket seals the outlet joint of the exhaust gas recirculation (EGR) system, where recirculated exhaust gas leaves the EGR valve/cooler ...
View full detailsKey Fob Cover Kit is a replacement outer cover for the remote smart key. The kit contains the upper and lower cover halves with the function butto...
View full detailsClip secures an exterior body moulding to the body panel. It is a retaining clip used in the body moulding assembly, holding a trim moulding in po...
View full detailsEGR Valve Gasket seals the exhaust gas recirculation valve to its mating face within the EGR and front exhaust system. Fitted on the left-hand ban...
View full detailsDrive Belt Tensioner for the front accessory (auxiliary) drive of the 3.0L V6 diesel engine. It maintains correct tension on the drive belt that ru...
View full detailsFan Bracket carries the secondary drive belt idler pulley within the front end accessory drive of supercharged petrol engines. It locates the idle...
View full detailsCV Boot Kit
Circuit Breaker installs within the electrical power distribution system, protecting a circuit against overcurrent by interrupting the supply when ...
View full detailsUtility Tray for the load compartment, part of the vehicle's tool and emergency equipment stowage. The moulded foam tray locates in the luggage ar...
View full detailsWheel Hub is part of the wheel-end assembly at the suspension corner. It carries the wheel bearing and provides the mounting flange for the road w...
View full detailsVacuum Pump supplying the brake servo on the supercharged AJ133 petrol engines (3.0L V6 and 5.0L V8). Forced-induction petrol engines cannot rely ...
View full detailsExhaust Gas Recirculation Gasket seals the exhaust gas recirculation (EGR) connection on the left-hand side, maintaining a gas-tight joint within t...
View full detailsExhaust Gas Recirculation Gasket seals the joint between the EGR cooler and the EGR valve on the right-hand side, maintaining a gas-tight connectio...
View full detailsIntercooler Pipe connecting the turbocharger outlet to the intercooler in the charge-air system of the 2.0L AJ200 (Ingenium) four-cylinder diesel e...
View full detailsClip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.
Fuel Pump is the in-tank pump module of the fuel delivery system. Mounted within the fuel tank, it draws fuel and delivers it under pressure to th...
View full detailsFront Bumper in black finish. This is the moulded front bumper assembly that mounts across the front of the vehicle, forming the lower front bodywo...
View full detailsFront Door Moulding - the exterior moulding/finisher fitted to the front door. It runs along the front door body panel as a protective and decorat...
View full detailsRear Wiper Blade for the rear window wiper. Sweeps water and debris from the rear screen to maintain rearward visibility.
Front Wiper Blade for the windscreen wiper, in the passenger-side (left-hand) position on right-hand-drive vehicles. Sweeps the windscreen to clea...
View full details