Products

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

MAP Sensor (Manifold Absolute Pressure sensor) for the engine management system, mounted on the throttle housing. It measures the absolute pressur...

Manifold Absolute Pressure (MAP) Sensor for the 3.0L V6 diesel engine. Mounted on the throttle housing, it measures the absolute pressure in the i...

Locking Flange Nut - M8 for fastening applications requiring vibration-resistant fixings. A prevailing-torque hexagonal nut with an integral flang...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Oil Filter Housing Cover is the cover for the cartridge-type oil filter assembly on 3.0 GDI petrol and 5.0 AJ-V8 engines. This cover retains the r...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Immobiliser Transceiver for the vehicle anti-theft (immobiliser) system. This is the transceiver aerial that reads the transponder in the key at t...

Brake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...

Brake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...

Gasket

EGR Inlet Gasket for the exhaust gas recirculation system on the 3.0L V6 turbo diesel engine. Seals the joint at the EGR inlet, where recirculated...

EGR Gasket Inlet

EGR Tube connecting the exhaust manifold to the EGR valve on the 3.0L V6 turbo diesel engine. Carries hot exhaust gas from the exhaust manifold to...

EGR Tube connecting the exhaust manifold to the EGR valve on the 3.0L V6 turbo diesel engine. Carries hot exhaust gas from the exhaust manifold to...

Sensor Assembly

Sensor Assembly

Fuel Return Pipe for the diesel fuel system return circuit, 3.0L V6 diesel applications. The return pipe carries surplus fuel not consumed by the ...

Exhaust Gas Temperature Sensor measures the temperature of the exhaust stream within the diesel exhaust and emissions system. It reports to the en...

Injector O-Ring is the lower sealing ring for a diesel fuel injector, used on 3.0L SDV6 and 4.4L TDV8 engines. It seals the lower body of the inje...

Automatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...

Automatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...

Automatic Transmission Fluid (ATF) for the automatic gearbox and power steering circuit. Specified as the transmission and power steering fluid to...

Output Shaft Oil Seal for the ZF 8HP eight-speed automatic transmission. Seals the transmission output shaft where it exits the gearbox housing, p...

Transmission Oil Pan & Filter Kit - the lower fluid pan for the ZF 8HP70 8-speed automatic transmission, incorporating an integrated fluid filt...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Bolt is a threaded fastener used across several assemblies, including door latch mechanisms, front seat bases and anti-lock braking system mounting...

Parking Sensor is a Park Distance Control (PDC) ultrasonic sensor mounted in the bumper, part of the parking aid system. It emits and receives ult...

Cylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...

Cylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...

Plastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...

Plastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...

Trim Clip - push-fit fastener securing exterior body mouldings, front and rear bumper trim and the radiator grille to the body panels. Renews an o...

Trim Clip - push-fit fastener securing exterior body mouldings, front and rear bumper trim and the radiator grille to the body panels. Renews an o...

Trim Clip - a plastic push-fit retaining clip used to secure exterior trim and body mouldings to the vehicle. It locates in a pre-drilled panel hol...

Lamp - Side Flasher

Lamp - Side Flasher

Oil Cooler Tube carries engine oil through the oil cooler circuit. The tube connects the engine oil system to the oil cooler, routing oil to be co...

Oil Cooler Tube forms part of the engine oil cooling circuit, carrying oil between the engine and the oil cooler. Used on 5.0L V8 and 3.0L V6 supe...

Body Moulding Retainer Clip, a lantern-type fastener for the vehicle's exterior trim. The clip secures exterior body mouldings - such as the rocke...