Products

Window Motor for the left-hand front door, part of the electric window mechanism. The motor drives the window regulator through its gearbox to rai...

Window Motor for the right-hand front door, part of the electric window mechanism. The motor drives the window regulator through its gearbox to ra...

Water Pump for the 2.5L VM Turbo Diesel engine, part of the Engine Coolant Circulation Assembly. The pump circulates coolant continuously through ...

Heater Blower Motor & Fan assembly for the cabin heating and ventilation system. The motor drives the fan that draws air through the heater box...

Heater Motor Adaptor Lead for the heater blower motor and fan assembly. This wiring adaptor bridges the blower motor to the vehicle's existing heat...

Fuel Stop Solenoid for the 200 Tdi and 300 Tdi 2.5L turbo diesel engine, mounted on the fuel injection pump. Held open while energised through the...

Injector Pipe for the No.4 cylinder of the 2.5L 200TDi diesel engine. This rigid high-pressure steel pipe carries metered fuel from the injection p...

Shaft 90/110 RH 31/10

Half Shaft - LH (Left-Hand), part of the Rear Axle Drive Assembly on the Defender 90, 110, and 130. This half shaft transmits drive torque from th...

Front Brake Caliper is the right-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fr...

Front Brake Caliper is the left-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fro...

Wiper Blade with a pin (bayonet) fitting for attachment to the wiper arm. Part of the windscreen wiper assembly, the blade holds the rubber wiping...

Voor alle LT77 versnellingsbakken

Fitment: All non ABS models (VIN) JA032851 on to (axle) 38L03120B. 39L05552B. 42L00521B. 43L18579B All Models From (A)57L00001B To (A)57L05188B0

Side Moulding is an exterior body trim strip for the 2-door body side. It runs along the side body panel to protect the paintwork from stone chips...

Front Mud Flap Kit, supplied as a left and right pair. Mounts behind the front wheel arches to reduce spray, mud, and stone throw from the front w...

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Rivet - a mechanical fastener used within the body and chassis assembly to join thin sheet metal and panel components. Nominal size 3/16" (4.8 mm)...

Front Hub Assembly, ABS configuration. Part of the front axle hub and bearing system. The hub locates the front wheel and carries it for rotation ...

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...

Wheel Hub Stud FRC5926 or RUF000020 for Defender 90 And 110, Discovery I and Range Rover Classic.

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Spring Retainer - rear inner-top retainer in the coil spring and shock absorber mounting. It locates and holds the top of the rear coil spring at ...

Spring Retainer secures the upper outer mounting of the rear coil spring and damper within the rear suspension assembly. It clamps the top of the ...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Radius Arm Cup Washer is the dished washer used at the front radius arm mounting, seating against the radius arm bush to spread the clamping load o...

Front Anti-Roll Bar Bolt secures the front anti-roll bar within the front suspension assembly. It fixes the bar to its mounting, holding it in pos...

Tailgate Lock Screw - Upper, an M5 x 20 countersunk screw for the upper tailgate lock mechanism. This countersunk screw secures the upper tailgate...

Countersunk Screw for the Transmission Brake Assembly. The countersunk head sits flush within the mating surface, maintaining correct alignment and...

Pan Head Screw, M4 x 12mm. Metric pan head screw for use across a range of Land Rover assemblies, including brake system and electrical components.

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Screw used as a body and underbody fixing across several assemblies, including the tailboard striker, the folding side-door step assembly, and the ...

Screw with a 1/4" UNF (Unified Fine) thread, 7/8" long, used as a setscrew in body, hinge and mirror-arm fixings. Note: non-metric (imperial UNF) ...

Brake Caliper Piston Kit - replacement pistons for the rear brake caliper. The pistons run in the caliper bores and, under hydraulic pressure, pre...

Screw - M8 x 25mm is a fastener used in the assembly of the LT230 transfer gearbox. The LT230 is a two-speed transfer box fitted to Defender, Disc...

Screw 1/4" UNF x 1" screw used as a fixing in the upper section of the rear tailgate assembly.

Setscrew used as a general-purpose fastener in engine bay ancillary and drivetrain assemblies. Applied at engine harness mounting points, bell hou...

Steering Stop Bolt - M12 x 50mm shouldered hex-head bolt for the front axle steering lock assembly. This bolt sets the maximum steering lock angle...

Screw hex HD 3/8" UNC x 1-1/4"

Hex-head screw, 1/4" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Hex-head bolt, 1/4" UNF thread, 7/8" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socket...

Bolt - a hexagonal-head bolt with a 1/4" UNF (Unified Fine) imperial thread and a 1-1/4" length. Used as a body and chassis fixing at points such a...

Hex-head bolt, 5/16" UNF thread, 1" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and sockets...

Bolt - a hexagonal-head bolt with a 3/8" UNF (Unified Fine) imperial thread and a 1" length. Used as a suspension and chassis fixing at points such...

Swivel Housing Gaiter Kit - protective rubber gaiters for the front axle swivel housing balls, within the front axle drive shaft and hub assembly. ...