Products

Top Coolant Hose for the engine cooling circuit. Carries hot coolant from the engine outlet at the thermostat housing to the top tank of the radia...

Pedal Rubber Pad for the foot pedal. The moulded rubber pad slips over the pedal arm to provide a durable, non-slip foot surface. Fitted to manual...

Ball Joint for the self-levelling suspension strut. Forms the pivoting connection at the end of the self-levelling unit, letting the strut articul...

Radiator for the engine cooling system, serving as the primary heat exchanger that dissipates heat from the coolant circulating through the 3.5L V8...

Clutch Release Fork operates inside the bellhousing as part of the manual transmission clutch release mechanism. Pivoting on its mounting in the c...

Clutch release fork kit used within the manual transmission clutch release mechanism. The release fork operates in the clutch housing and transfers...

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Grommet - Safety Harness Anchorage

Accelerator Cable for left-hand-drive applications, forming part of the throttle control linkage. The cable connects the accelerator pedal to the ...

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Speedometer Cable – LHD is the mechanical drive cable that transmits road speed to the speedometer. The rotating inner core runs inside a protectiv...

Trailer Plug - a 7-pin towing electrics connector. Wired into the towing vehicle's harness, it mates with the trailer or caravan socket to feed th...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Side Repeater Lamp - Front is part of the exterior lighting system, mounting in the front wing to give a side-on indication of the direction indica...

switch loss vacuum

Grommet

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Anti-Squeal Shim is a thin damping shim for the rear disc brake assembly. It fits between the brake pad backing plate and the caliper piston, isol...

Anti-Squeal Shim for the rear brake pads - left-hand side. This shim fits between the brake pad backing plate and the caliper piston to dampen vib...

Clutch Release Plate for the LT77 5-speed manual gearbox clutch release assembly. This mounting plate fastens the external hydraulic clutch slave ...

Exhaust mounting spacer tube

Mainshaft Bearing

Bottom cover seal

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Bearing needle roller

Rear Silencer & Tailpipe for the V8 single exhaust system. This is the rearmost section of the exhaust, combining the rear silencer and tailpi...

Centre Silencer for the V8 single exhaust system. This intermediate silencer sits between the front (down) pipe and the rear silencer, providing t...

Core Plug (cup/expansion plug) seals a casting core hole in the cylinder block, fitted at the rear of the block. It closes the openings left by th...

Bottom radiator hose RRcl >'85

Rear Brake Hose for the rear hydraulic braking circuit. This flexible hose carries brake fluid from the rigid chassis-mounted brake line to the re...

PDWA valve

Magnetic Drain Plug for the engine oil sump and the LT230 transfer box drain ports. The magnetised tip captures ferrous wear particles suspended i...

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Power Steering Filter for the power-assisted steering (PAS) fluid reservoir, part of the Steering Hydraulic Circuit. This filter element sits insi...

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Oil Pump Relief Valve Spring for the 3.5L V8 petrol engine lubrication system. The spring sets the opening pressure of the oil pump pressure-relie...

Sump Gasket for the Rover V8 petrol engine oil sump assembly. This gasket is fitted between the oil sump (oil pan) and the engine block, forming a...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Rocker Assembly Aluminium - LH

Inlet Valve for the 3.5L V8 petrol engine in 8.25:1 compression specification. The valve opens against the inlet port to admit the air/fuel charge ...

Cylinder Head Bolt - a 7/16" UNC x 2-1/4" short-type bolt for the Rover V8, part of the cylinder head fixings. This is the shorter of the head bol...