Products

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Clip

Battery - Wet Non-Spillable for the vehicle electrical system. It is a flooded (wet) lead-acid battery of sealed, non-spillable construction. It su...

Crankshaft Oil Seal – Rear seals the rear of the crankshaft where it exits the cylinder block, retaining engine oil at the crankshaft-to-transmissi...

Thermostat Housing Gasket in the engine cooling system. This 37 mm gasket seals the joint between the thermostat housing and the engine on AJ-V8 4...

Timing Cover Seal for the AJV8 petrol engine - a rubber seal fitted to the timing gear cover. It seals the timing gear cover against the cylinder ...

Water Pump in the engine cooling circuit, for AJ-V8 4.4L and 4.2L Supercharged petrol engines. This pump circulates coolant through the engine blo...

Water Pump Gasket

Head Gasket - V8 - LH seals the left-hand cylinder head to the engine block on the 4.4L AJ-V8 petrol engine. It forms the gas-tight joint between ...

Sender Assembly

Throttle Body Gasket A gasket that seals the joint between the throttle body and the intake on the supercharged 4.2L V8 petrol engine. It seals th...

Cylinder Head Gasket - LH seals the left-hand cylinder head to the engine block on the 4.2L V8 Supercharged petrol engine. It forms the gas-tight ...

Exhaust Valve for the AJV8 petrol engine, fitted in the cylinder head valvetrain. It opens to release combustion gases into the exhaust port and s...

Crankshaft Pulley Bolt for the AJ-V8 petrol engine. It secures the crankshaft pulley and torsional vibration damper to the nose of the crankshaft, ...

Ignition Coil for the AJ-V8 petrol engine. This coil is of the coil-on-plug type, fitted one per cylinder, mounting directly over the spark plug to...

Battery Terminal Disconnect Switch Green Knob

Pack piece

Fuel Tank Mounting is the moulded rubber isolator in the fuel tank mounting assembly that sits between the tank body and its chassis support. It c...

Stub Axle Gasket for the rear drive shaft assembly on Land Rover Series II, IIA, and III. This gasket seals the stub axle flange at the rear axle ...

Intermediate Exhaust Pipe - the centre section of the exhaust system, connecting the front down-pipe to the rear silencer. Routes exhaust gas rear...

Shim plate

Layshaft First Gear - the first-speed gear on the layshaft (countershaft) of the main gearbox. Meshes with the corresponding mainshaft gear to pro...

Mainshaft Gear - 1st Speed is a 29-tooth first-speed gear that runs on the mainshaft within the manual gearbox gear train. As a non-synchronised c...

Flasher Unit is the 3-pin relay in the direction indicator circuit that switches the turn signal lamps on and off at a regular rate. Wired between...

Handbrake Catch Pawl, the ratchet claw of the transmission parking brake mechanism. It engages the toothed quadrant on the handbrake lever, lockin...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

Exhaust Connecting Pipe is the intermediate section of the exhaust system, joining the front pipe to the rear silencer. It carries exhaust gas alo...

Brake Shoe Spring for drum brake assemblies. This return spring draws the brake shoes away from the drum surface when the brake pedal is released,...

Brake & Clutch Reservoir Tank Kit, a replacement for the original single fluid reservoir that fed both the brake and clutch master cylinders. ...

Distance Piece - a machined spacer in the axle and suspension assembly, specified for the 1-Ton Military configuration. It sets the standoff betwe...

Fuel Cap closes and seals the fuel tank filler neck on petrol applications. It uses a two-lug bayonet fixing that locates and locks into the fille...

Fuel Cap Locking Hasp is the body-mounted latch in the fuel filler arrangement that secures the petrol filler cap against unauthorised opening. It...

Headlamp bulb 12V 40/45W duplo (non-halogen)

Fuel Filler Cap Seal is the sealing ring fitted inside the metal fuel filler cap. It forms the seal between the cap and the filler neck, preventin...

Self-Locking Nut, 3/8" BSF, used to secure propshaft fasteners within the drivetrain. The deformed thread form provides a self-locking action that...

Exhaust Downpipe is the front section of the exhaust system, connecting the exhaust manifold outlet to the intermediate pipe. This downpipe fits L...

Rocker cover rubber washer petrol

Flywheel Ring Gear for four-cylinder petrol engines. The ring gear is shrink-fitted to the periphery of the flywheel and meshes with the starter mo...

Tappet Screw - the valve-clearance adjusting screw in the rocker gear of the four-cylinder engine (3-bearing crankshaft), part of the valvetrain. ...

Screw - a threaded fastener supplied as a single replacement screw.

Tappet kit

Swivel Pin Housing Locking Plate mounts to the front axle swivel pin housing. It locks the swivel pin in position and provides the fixed stop that...

Bolt with a 3/8" UNF (Unified National Fine) thread and a 1-7/32" length. A standard imperial-thread fastener for chassis, driveline and body fixi...

Spring Shackle Distance Tube for the rear leaf spring shackle assembly. This spacer tube sets the correct spacing between the shackle plates, maint...

Accelerator pedal pad S3