Products

Bush - Accelerator Linkage is a small bearing bush fitted to the accelerator linkage assembly on the 2.6L 6-cylinder petrol engine used in Series I...

Gearbox Cover Plate Gasket for the LT76 gearbox. This rubber gasket seals the cover plate to the gearbox casing, sealing the joint against oil lea...

Clutch Slave Cylinder Repair Kit overhauls the clutch slave cylinder within the hydraulic clutch release circuit on the LT77 manual gearbox. The s...

Headlamp Bulb for the headlamp lighting circuit, rated for 24-volt electrical systems. This is a pre-focus type bulb: a locating flange on the cap...

Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...

Handbrake Expander operates the transmission-mounted drum handbrake, forcing the brake shoes apart against the drum when the handbrake is applied. ...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Handbrake Locking Plate for the rod-operated transmission handbrake - the drum-type parking brake mounted at the transfer gearbox output. The plat...

Spring plate

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Steering Box Side Plate Gasket seals the side cover plate against the casing of the manual steering box. It sits between the dowel-located side pl...

This brake drum is designed for long wheelbase Land Rover Series II and Series IIA vehicles. It is a drum brake component intended for use in tradi...

Exhaust Front Pipe for the 2.25L petrol engine, forming the first section of the exhaust system between the manifold and the intermediate pipe. It...

Exhaust Front Pipe in stainless steel, forming the first section of the exhaust system for the 2.25L petrol engine, between the manifold and the in...

Wiper Gear Linkage for the windscreen wiper system, transmitting drive from the wiper motor to the wheelbox and wiper spindle. It converts the rot...

Air Intake Hose for the 2.25L and 2.6L petrol induction system. This flexible rubber hose connects the air filter housing to the carburettor intak...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Brake master cyl SII SWB

Screw - a set screw for the gearbox top cover plate. It secures the cover plate to the top of the main gearbox casing. Not used on the Stage 1 V8 ...

Washer used within the ignition system of four-cylinder petrol engines, associated with the distributor, ignition coil, HT leads and spark plug ins...

Crankshaft Oil Seal is the outer (rear) crankshaft seal in the engine sealing arrangement, fitted where the crankshaft exits the cylinder block. S...

Grab Handle for the rear end door, mounted externally on the rear door casing. It provides a fixed handhold at the rear of the vehicle, giving a s...

Cup Plug - a cup-type core plug (also known as an expansion or welch plug) that seals a casting core hole in the cylinder block or cylinder head. ...

Core Plug, 1 7/8" diameter, sealing a casting core hole such as those in the inlet manifold and engine castings. Core plugs close the openings lef...

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Bottom End Gasket Set for the overhaul of the 2.25L diesel engine (3- and 5-main-bearing), covering the gasket and joint requirements of the lower ...

Track Rod Tube - 109.5cm - Part-Threaded Ends

Thermostat Gasket for the thermostat housing on the 2.25L petrol engine. This paper gasket seals the thermostat housing to the cylinder head, prev...

Thermostat O-Ring for the 2.25L petrol engine cooling system. This O-ring provides a coolant-tight seal within the thermostat housing assembly. It...

Gudgeon Pin Bush - the small-end bush pressed into the connecting rod for the gudgeon pin. It forms the bearing surface between the gudgeon (pisto...

lock washer. sold EACH.

Clutch Withdrawal Unit Gasket - seals the mounting joint where the clutch withdrawal (release) housing bolts to the gearbox bellhousing. Part of t...

Gearbox Front Layshaft Bearing for the LT76 main gearbox, supporting the front end of the layshaft (cluster gear) within the gearbox casing. It ca...

Gearbox Distance Piece

Stud securing the transfer box to the LT76 gearbox. Threaded stud at the transfer box-to-gearbox mating face, clamping the two housings together a...

Waterpump pulley

Shim .003" for swivel pins

Swivel Pin Shim, 0.005" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Swivel Pin Shim, 0.010" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Swivel Pin Shim for the front axle swivel housing assembly. This 0.030" shim is fitted beneath the upper swivel pin retaining plate and is used to ...

Swivel Pin Lock Tab for the front swivel pin housing on Land Rover Series II, IIA, and III. Fitted to the 7/16 BSF studs that retain the swivel pi...

Steering Relay Arm - Upper is the upper lever of the steering relay unit, the vertical relay mounted on the front chassis crossmember that transfer...

Stud for the front axle swivel pin housing - a threaded stud that provides a fixed anchor for fastening a mating component to the swivel pin housin...

Lower Swivel Pin O-Ring for the front axle swivel housing assembly. It seals the joint at the lower swivel pin, where the steering arm and lower pi...

Swivel Housing Stud with 7/16" BSF thread, fitted to the lower face of the front axle swivel housing. The stud secures the lower swivel pin bracke...