Products

Oil Cooler Return Pipe for the engine oil cooling system of the Defender, carrying cooled oil from the oil cooler back to the engine. This pipe is...

Rear Bumper in a black finish, forming the rearmost impact member bolted to the rear chassis crossmember. Supplied less the styling kit, so it com...

Power Steering Hose is a flexible hydraulic hose in the power steering circuit. It carries pressurised hydraulic fluid through the steering system...

Engine Mounting - Front is a rubber-to-metal bonded mount that supports the front of the engine on the chassis. It carries the engine's weight at ...

Coil Spring for the suspension system of the Range Rover Classic, for left-hand drive (LHD) variants. This left-hand spring is identified by its g...

Bumper Mounting Bracket - front bumper mounting, left-hand side. This bracket forms part of the front bumper mounting and secures the bumper to th...

O-Ring sealing the air filter housing to the airflow meter on V8 EFI engines. This O-ring seals the joint between the air filter housing outlet an...

Cable Accelerator Later Classic Throttle 2.5dna, TD From (V)267062 LHD - 90/110

Clutch Hose for the hydraulic clutch actuation system. This flexible hose provides the hydraulic connection between the rigid clutch pipework and t...

Brake Hose - flexible hydraulic line in the rear braking circuit, connecting the chassis-mounted rigid brake pipe to the rear axle brake assembly. ...

Accelerator Cable linking the accelerator pedal to the throttle. This Bowden cable transfers movement of the accelerator pedal to the throttle lin...

Handbrake cable from the handbrake actuation assembly, linking the handbrake lever to the transmission brake mounted on the transfer box rear outpu...

Hand Throttle Control Cable for the Defender, allowing the driver to set and hold a fixed engine speed independently of the accelerator pedal. The...

Flexible Steering Shaft Coupling located in the steering column intermediate shaft, joining the steering column to the steering box input. The fle...

Bottom hose

Choke Cable for the V8 carburettor engine, part of the manual choke control system on right-hand drive Defender 90 and 110 models. This cable conn...

Choke Cable for the carburettor cold-start circuit, connecting the dashboard-mounted choke control to the carburettor choke linkage. When pulled, ...

Exhaust pipe V8 EFI

Intermediate Exhaust Pipe for the 2.5TD turbo diesel engine, forming the centre section of the exhaust system on Defender 90 and 110 models. This ...

Front Bumper in a black finish, forming the front impact member bolted to the front chassis crossmember. Incorporates the provision for the headla...

Radiator Top Hose for the 200TDi 2.5L turbo diesel cooling circuit. Connects the engine outlet at the thermostat housing to the top inlet of the r...

Exhaust Front Pipe (down pipe) for the 2.5L turbo diesel (non-TDi) exhaust system. Connects the turbocharger/manifold outlet to the intermediate e...

Exhaust centre silencer 110 V8 from vin266790

Exhaust Silencer - Front for the Defender 90, fitting naturally-aspirated 2.5L petrol and 2.5L diesel engines. This silencer forms the forward sec...

Radiator Hose for the 2.4L 4-cylinder turbo diesel cooling circuit. Connects the engine to the radiator, carrying coolant between the two as part ...

Radiator Top Hose in the engine cooling circuit, connecting the radiator to the upper coolant pipe. It carries heated coolant from the engine's up...

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the fuel injection pump. It transmits pedal movement to the...

Power Steering Hose routed between the steering box and the power steering pump. It forms part of the power steering hydraulic circuit, carrying fl...

Power Assisted Steering Hose for the 4-cylinder non-Tdi engine, part of the hydraulic steering circuit on right-hand drive Defender 90 and 110 mode...

Front bumper end cap, right-hand side, from the front bumper assembly. The end cap closes off the outboard end of the front bumper where the bumpe...

Front Bumper End Cap - Left Hand is the moulded outer closure panel of the front bumper assembly. It fits over the outboard end of the front bumpe...

Rear Bumper End Cap for the left-hand (LH) outboard end of the rear bumper assembly, finished in black. The end cap closes off the open end of the...

Rear Bumper Reflector for the Discovery 1, fitting the designated aperture in the rear bumper to meet lighting regulations. The red retro-reflecti...

Grab Handle chassis-mounted exterior fitting, bolted to the vehicle chassis. It provides a fixed hand-hold at the chassis, giving a secure grab po...

Rear Bumper End Cap - Right Hand for the Range Rover Classic, forming the right-hand closing section of the rear bumper assembly. This end cap fit...

Front Bumper Securing Bolt for fastening the front bumper to the chassis crossmember. M10 thread, 120 mm long, with a black finish.

Exhaust Pipe for the 3.5L V8 EFI exhaust system, catalyst configuration. The pipe forms part of the exhaust gas path on catalytic-converter-equipp...

Bottom Radiator Hose for the engine cooling circuit on the V8 Petrol engine. Connects the lower outlet of the radiator to the coolant pump inlet o...

Exhaust Bracket for the exhaust system mounting. The bracket supports and locates a section of the exhaust line against the underbody, typically w...

Radiator Hose – Top for the engine cooling system. The upper hose carries hot coolant from the engine outlet to the top of the radiator, where heat...

Top Radiator Hose forms the upper connection of the engine cooling circuit, carrying heated coolant from the thermostat housing outlet to the radia...

Fuel Tank Cradle - the support cradle that carries the fuel tank beneath the vehicle, bolting to the chassis to hold and locate the tank. Heavy-du...

Oil Cooler Hose for the engine oil cooling circuit on the V8 engine. Forms part of the hose assembly linking the engine oil cooler to the oil circ...

Fuel Pump Seal for the fuel tank sender unit. This seal seats at the mounting flange of the fuel pump and sender unit where it interfaces with the ...

Sealing Grommet seals the aperture in the fuel tank top face around the fuel pump or tank sender unit. It sits between the pump or sender flange a...

Fuel Filter is the in-line filter for the pressurised supply side of the V8 EFI fuel injection system. It is mounted in the fuel line between the ...

Power Steering Hose - the high-pressure feed line in the power steering hydraulic circuit. It carries pressurised fluid from the power steering pu...