Products

Brake shoe spring 109 rear lower

Upgrade and restore the swivel housing assembly on your Land Rover Series 2 with this swivel pin conversion kit. Designed for improved durability a...

Thermostat for the engine cooling circuit, controlling coolant flow between the engine and radiator. The valve stays shut while the engine warms f...

Swivel Pin - a front axle steering swivel pin for the swivel housing. It provides a pivot on which the swivel housing turns, carrying the stub axl...

Gearbox Selector Pad for the LT77 five-speed manual gearbox. Fits the 5th gear selector within the selector and yoke assembly, forming the bearing...

Rear Halfshaft for the E.N.V. heavy-duty rear axle, right-hand side. The halfshaft transmits drive from the differential through the axle casing t...

Rear Halfshaft for the E.N.V. heavy-duty rear axle, left-hand side. The halfshaft transmits drive from the differential through the axle casing to...

Hex Nut - 7/16 UNF fixing nut. Used on the fuel pipe unions of the 3.5L V8 twin-carburettor petrol engine. Also supplied as part of a service kit.

Olive compression ferrule for a pipe union. The olive seats between the pipe and the union nut, forming a compression seal at the joint as the nut...

Hood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...

Rear Leaf Spring for Series IIA and Series III 109" wheelbase 1-ton and Extra Heavy Duty Land Rovers. Suitable for both left-hand and right-hand si...

Engine Plug (3/8 BSF thread) for Land Rover 4-cylinder petrol and diesel engines. This threaded blanking plug is used at multiple points across th...

Clevis Pin for the clutch cross shaft, part of the mechanical clutch release linkage. The pin forms the pivoting joint that connects the clutch op...

Barrel Lock & Key is the lock barrel and matching key for the ignition/starter switch. This is the diesel-application barrel for the earlier t...

Wheel Brace for loosening and tightening road wheel nuts. It has a 15/16 in AF (approximately 24mm) hexagon socket, sized for the wheel nuts fitted...

Spring Shackle Plate forms part of the rear leaf spring shackle assembly, pairing with the shackle pins and bushes to connect the swinging eye of t...

Shackle plate

Shackle plate

Shackle Plate for the rear leaf spring shackle assembly. The shackle plate links the rear eye of the leaf spring to the chassis mounting, allowing ...

Shackle Pin (9/16 UNF × 4-3/8 in.) for the rear leaf spring assembly on Land Rover Series vehicles. This is the short shackle pin, fitted at the r...

Shackle Pin (9/16 UNF × 4-1/2 in.) for the leaf spring suspension on Land Rover Series vehicles. This medium-length pin is used at the forward (ch...

Shackle Pin - Long (9/16 UNF × 5-1/4 in.) for the front leaf spring shackle on Land Rover Series vehicles. This long shackle pin is fitted at the ...

Steering Relay Shaft Bush - Split Half for the steering relay assembly on classic Land Rover models. This bush is supplied as one half of a split ...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Crankshaft Thrust Washer - 0.0075in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksh...

Crankshaft Thrust Washer - 0.010in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksha...

Water Pump Gasket - 9-Hole for the cooling system on Land Rover Series 2.25L Petrol engines. This gasket seals the mating face between the water p...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Railko Bush is the lower swivel bearing in the front axle swivel pin housing. It locates the bottom swivel pin and provides the low-friction pivot...

Drain Plug for the gearbox, transfer box and axle casings. It threads into the drain point at the base of the casing to retain the oil in service, ...

Dipstick Tube for the engine lubrication system on non-V8 four- and six-cylinder engines. The tube fits into the cylinder block and guides the oil ...

Crankshaft Rear Oil Seal Kit - Cork for the rear crankshaft sealing assembly on Series Land Rover engines with a 3-bearing crankshaft. This kit su...

Crankshaft Oil Seal Kit for a full rear crankshaft seal replacement on Series Land Rover engines with a 3-bearing crankshaft. This kit includes tw...

U-Bolt for the leaf spring suspension, clamping the front leaf spring to the axle. This is the short, round-top type with a 7/16" BSF thread. It p...

Fuel Filler Hose - SWB for the fuel filler assembly on Series Land Rovers equipped with an under-seat fuel tank. This rubber hose connects the ext...

Fuel Filler Breather Hose, part of the fuel filler and tank ventilation system. The hose vents air displaced from the fuel tank during refuelling,...

Fuel Tank Plate - Rear Fixing is the mounting plate used to secure the rear of the fuel tank on 88" wheelbase Series Land Rovers. It provides the s...

Fuel Tank Suction Pipe for the under-seat fuel tank. The pipe forms the tank-side pickup of the fuel supply circuit, drawing fuel from within the t...

Oil Filler Breather Cap of the top-hat type closes the oil filler on the cylinder head side cover and vents the crankcase. It combines the oil fil...

Sump Gasket seals the joint between the sump (oil pan) and the base of the cylinder block on the 2.6L six-cylinder IOE petrol engine. It forms the...

Fuel Sender Unit Gasket for the fuel gauge sender unit fitted to the fuel tank. This gasket seals the joint between the sender unit flange and the...

Engine Push Rod for diesel engine valve actuation, operating within the cylinder head valve train. The push rod transmits motion from the camshaft...

Sump Gasket - 4-Cyl for the engine sump sealing joint on Land Rover 4-cylinder engines. This gasket seals the mating face between the sump pan and...

Brake Shoe Return Spring for the rear drum brake assembly, fitted at the upper end of the brake shoes adjacent to the wheel cylinder. The spring h...

Spring Bush for the leaf spring suspension system on Series Land Rovers. This rubber bush fits into the spring eye at the front fixed mount and re...