Products

ACE Seal Kit for the Active Cornering Enhancement valve block. The ACE system operates hydraulic actuators on the front and rear anti-roll bars to...

Sealing Washer - a sealing washer used at the front suspension strut mounting. It seats at the strut fixing to seal and settle the joint while mai...

Washer Adjusting washer for the rear suspension arm mounting. Part of the rear multi-link suspension assembly, it locates at the suspension arm pi...

Eccentric Washer - an adjusting washer used at the front suspension arm pivot mounting. The offset (eccentric) hole allows the arm's pivot bolt po...

Washer Dowty sealing washer for the Active Cornering Enhancement (ACE) hydraulic anti-roll system. It seals the pipe-to-actuator union, fitting at...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Spring Retainer - rear inner-top retainer in the coil spring and shock absorber mounting. It locates and holds the top of the rear coil spring at ...

Spring Retainer secures the upper outer mounting of the rear coil spring and damper within the rear suspension assembly. It clamps the top of the ...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Radius Arm Cup Washer is the dished washer used at the front radius arm mounting, seating against the radius arm bush to spread the clamping load o...

Bolt - M12 x 73mm for the adjustable rear bottom link on the Freelander 1. Secures the rear lower suspension arm's adjustable pivot mounting, form...

Bolt Mounting bolt for the rear suspension arm. Part of the rear multi-link suspension assembly, it secures a rear upper or lower suspension arm a...

Bolt Mounting bolt for the front suspension arm. Part of the front suspension assembly, it secures a front upper or lower control arm (wishbone) a...

Flanged Bolt - M10 x 50, a Grade 10.9 high-tensile fixing used in the front drive shaft and hub assembly. It secures the drive member (drive flang...

Front Anti-Roll Bar Bolt secures the front anti-roll bar within the front suspension assembly. It fixes the bar to its mounting, holding it in pos...

Rear Anti-Roll Bar Bolt secures the rear anti-roll bar within the rear suspension assembly. It fixes the bar to its mounting, holding it in positi...

Bolt for the rear suspension assembly. This fastener is used in the rear cross member and stabilizer bar assembly, and in the rear knuckle and low...

Special Nut - secures the rear knuckle to the lower and upper suspension arms. It retains the rear suspension arm bolts at the knuckle, holding th...

Adjusting Nut is an M17 flanged nut used in the rear suspension toe link assembly. It locks the toe link adjuster at its connection to the rear kn...

Nut rear suspension arm M13

This special nut (thread size M14) is used in the rear suspension system across several Land Rover and Range Rover models. It plays a crucial role ...

Flanged Nut M16 flanged nut for the rear suspension arm fixings. Part of the rear multi-link suspension assembly, it secures the lower and upper s...

Knuckle Joint Bolt - an M14 x 88mm hex flange bolt securing the rear knuckle to the rear cross member. The integral flange spreads clamp load acro...

Suspension Bolt, M14 x 81mm, from the rear knuckle and suspension arm assembly. It secures a rear suspension arm at its knuckle mounting, passing ...

Circlip for the lower steering knuckle bush. This circlip retains the bush within the lower steering knuckle, forming part of the front axle and s...

Towing electrics kit - 7-core cable and socket assembly for the rear towing electrics circuit. Supplied pre-wired with approximately 1.5 m of 7-co...

Single socket plate - mounting plate for one towing electrics socket, part of the rear towing electrics installation. It provides the fixed mounti...

Pre-wired towing electrics - socket and cable assembly for the rear towing electrics circuit. The socket is supplied already wired to its cable ta...

Tailgate Lock Screw - Upper, an M5 x 20 countersunk screw for the upper tailgate lock mechanism. This countersunk screw secures the upper tailgate...

Countersunk Screw for the Transmission Brake Assembly. The countersunk head sits flush within the mating surface, maintaining correct alignment and...

Accelerator Pedal Pad - the moulded rubber cover that fits over the accelerator pedal. It provides a grippable, wear-resistant contact surface for...

Brake Disc - vented front brake disc, part of the front disc brake assembly. The disc is mounted to the front hub and rotates with the road wheel;...

Brake disc front D2

Brake disc rear

Brake Disc Rear XS

Front Brake Disc - solid (non-vented) front brake disc, 262 mm diameter. Provides the friction surface that the front brake pads clamp against to ...

Front Brake Disc - vented, 277 mm diameter. Part of the front brake discs and calipers assembly. The disc mounts to the front hub flange and provi...

Brake Disc Front L-322

Brake Drum - rear brake drum, part of the rear drum brake assembly. The drum fits over the rear brake shoes and rotates with the wheel hub. When t...

Rear Brake Drum for the rear drum brake assembly. The drum locates on the rear hub and provides the machined friction surface that the brake shoes ...

Transmission Brake Drum for the LT230 transfer box transmission brake - the drum-type parking brake mounted on the transfer box rear output. The d...

Pan Head Screw, M4 x 12mm. Metric pan head screw for use across a range of Land Rover assemblies, including brake system and electrical components.

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Screw used as a body and underbody fixing across several assemblies, including the tailboard striker, the folding side-door step assembly, and the ...

Pan Head Screw, M8 x 25mm. Metric pan head screw for use across Land Rover body, chassis, and accessory fitment applications.