Products

Axle Check Strap limits the downward travel of the rear axle, fitted within the rear suspension on the 1-Ton chassis running the Salisbury axle. I...

Accelerator Cable links the accelerator pedal to the injection pump throttle lever, forming part of the throttle linkage on the 2.25L diesel engine...

Check strap 109"" 88cm long

Bottom radiator hose RRcl >'85

Rear Brake Hose for the rear hydraulic braking circuit. This flexible hose carries brake fluid from the rigid chassis-mounted brake line to the re...

Past op alle benzine en diesel 109"" modellen (knevel sluiting)

cable choke S3 - Right Hand Drive 2.25L 4-cylinder petrol fitted with steering column lock, - Left Hand Drive 2.6L 6-cylinder petrol fitted with s...

Choke Cable is the manual choke control cable in the carburettor fuel system, running from the dashboard choke knob to the carburettor choke lever....

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Stop Cable Diesel Without Steering Column Lock RHD

Engine Stop Cable for the fuel shut-off control of the 2.25L diesel engine. Operating within the fuel injection circuit, the cable links the dashb...

Exhaust silencer and tailpipe LWB

PDWA valve

Rear Halfshaft for the Rover-type rear axle, right-hand side. The halfshaft transmits drive from the differential through the axle casing to the r...

Magnetic Drain Plug for the engine oil sump and the LT230 transfer box drain ports. The magnetised tip captures ferrous wear particles suspended i...

Distance piece

Fitment: All models to 1980 except V8

Rear Axle Stub for the rear axle assembly on early Series Land Rovers. The axle stub is the outboard section of the rear axle shaft assembly, carr...

Needle Roller Bearing for the transfer box intermediate gear. The bearing carries the intermediate gear on its shaft within the gear cluster, allo...

Wheel Cylinder - LH Front for the front drum brake assembly on long wheelbase Series models. This hydraulic wheel cylinder is mounted at the left-...

Wheel Cylinder - RH Front for the front drum brake assembly on long wheelbase Series models. This hydraulic wheel cylinder is mounted at the right...

Wheel Brake Cylinder Overhaul Kit for the drum brake hydraulic circuit. This kit provides the renewable seal components required to overhaul the f...

Flywheel for the 2.25L petrol engine in its 3-main-bearing configuration. Bolted to the rear flange of the crankshaft, the flywheel stores rotatio...

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Gearbox Gasket Kit - No Seals for the 4-speed manual gearbox and transfer box on Series models. This set supplies the paper and fibre mating gaske...

Propshaft Yoke for the propshaft flange joint, part of the Drivetrain assembly. This flange yoke bolts to the transfer case or axle flange and acc...

Power Steering Filter for the power-assisted steering (PAS) fluid reservoir, part of the Steering Hydraulic Circuit. This filter element sits insi...

O-Ring for the Zenith carburettor, part of the Fuel System assembly on the 2.25L 4-cylinder petrol engine. This O-ring provides a fluid-tight seal...

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Oil Pump Relief Valve Spring for the 3.5L V8 petrol engine lubrication system. The spring sets the opening pressure of the oil pump pressure-relie...

Sump Gasket for the Rover V8 petrol engine oil sump assembly. This gasket is fitted between the oil sump (oil pan) and the engine block, forming a...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Rocker Assembly Aluminium - LH

Inlet Valve for the 3.5L V8 petrol engine in 8.25:1 compression specification. The valve opens against the inlet port to admit the air/fuel charge ...

Cylinder Head Bolt - a 7/16" UNC x 2-1/4" short-type bolt for the Rover V8, part of the cylinder head fixings. This is the shorter of the head bol...

Rocker Cover Gasket for the V8 petrol engine, cork construction. The gasket seals the joint between the rocker cover and the cylinder head, contai...

Thermostat for the engine cooling system, with an 82°C opening temperature. The thermostat regulates coolant flow between the engine and the radia...

Cylinder Block Drain Tap threads into the coolant jacket of the cylinder block, providing a controlled drain point for the engine cooling system. ...

Rear Anti-Roll Bar Link connects the rear anti-roll bar (stabiliser bar) to the suspension. The link transfers load between the anti-roll bar and ...

Flame Trap fits into the crankcase ventilation circuit of the V8 twin-carburettor petrol engine, between the crankcase breather and the carburettor...

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Sump Plug seals the drain aperture at the base of the engine sump, retaining the engine oil and providing the drain point for an oil change. Remov...