Products

Washer is a thrust wafer for the upper swivel pin in the front axle swivel pin housing. It seats against the upper swivel pin and works alongside ...

Clutch Driven Plate (friction disc) for the clutch assembly, 9 1/2 inch diameter. The driven plate is clamped between the flywheel and the pressur...

Camshaft Position Sensor monitors the rotational position of the camshaft and reports it to the engine ECU. The ECU uses this signal to identify c...

Depression Control Valve mounted on the camshaft cover of the diesel engine. It regulates the internal depression (vacuum) of the engine, maintain...

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Water Pump for the 4.4L V8 petrol engine, forming part of the coolant circulation circuit. Driven by the accessory drive belt, the pump circulates...

Gasket Genuine LR

Breather Hose - the lower hose in the engine crankcase breather (crankcase ventilation) circuit. It carries crankcase blow-by gases away from the ...

Breather Hose - the upper hose in the engine crankcase breather (crankcase ventilation) circuit. It carries crankcase blow-by gases away from the ...

Heater valve

Clutch slave cylinder overhaul kit

Stud used at the gearbox-to-chassis bracket mounting on Series models. A 7/16" BSF stud securing the gearbox mounting bracket to the chassis. Not ...

Spherical Bearing Bush - Clutch Cross Shaft for Series 1, Series 2, and Series 3 Land Rover vehicles. The clutch cross shaft is supported at its p...

Fuel Tank Mount is a rubber mounting that supports the fuel tank on the chassis. It cushions the tank on its mounting bracket, isolating it from c...

Air Intake Hose for the 2.25 litre diesel engine, forming part of the air induction system between the air cleaner and the intake manifold. It car...

Gasket thermostat by-pass Series 2.25 petrol and diesel.

Cam Follower (tappet) in the valvetrain, riding on the camshaft lobe to transmit its motion to the pushrod and valve. It converts the rotating cam...

clamp exhaust

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Brake Master Cylinder for the braking hydraulic system, converting brake pedal force into hydraulic pressure to actuate the brakes. Mounted to the...

Heater Hose – Inlet carries hot coolant from the engine cooling circuit to the heater matrix, forming part of the cabin heating system. The inlet ...

Tailpipe forming the rearmost section of the exhaust system on Series Land Rovers equipped with the 2.6L 6-cylinder engine. This pipe routes exhau...

Festoon Bulb - 12V 21W is a double-ended festoon-type incandescent bulb rated at 12V 21W, fitted with contacts at both ends for installation in spr...

Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...

Exhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...

Bolt – 3/8" BSF x 1-1/4" is a threaded fastener used in the front axle assembly, securing the swivel pin housing. The bolt has a 3/8 inch diameter...

Chassis Shackle Bush – Front is the compliant bush at the chassis end of the front spring shackle, part of the leaf spring suspension mounting. Th...

Chassis Shackle Bush – Front – Polyurethane is a set of four polyurethane bushes for the chassis end of the front spring shackles, part of the leaf...

Brake master cylinder LWB post-80

Spring Shackle connecting the end of a leaf spring to the chassis bracket, allowing the spring to lengthen and shorten as it deflects under load. ...

Shackle Plate, the side plate of the spring shackle assembly that forms the swinging link between the leaf spring eye and the chassis shackle brack...

Front Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...

Front Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Oil Pump Relief Plunger is the pressure-relief valve plunger within the engine oil pump, part of the lubrication system on the 3.5L V8 petrol engin...

Folding side step Series

Carburettor Needle is the tapered metering needle that sets the fuel mixture in the carburettor. The needle moves within the jet to control fuel d...

Pinion Lock Nut – Salisbury secures the drive pinion in the Salisbury rear differential, retaining the pinion flange and holding the pinion bearing...

Fuel Hose for the 3.5L V8 twin-carburettor engine, part of the carburettor fuel supply plumbing. It connects the fixed points in the fuel feed lin...

Oil Seal – Rear Output Shaft seals the rear output shaft of the LT95 combined gearbox and transfer box, preventing oil leakage where the shaft exit...

Speedometer Drive Cable transmits rotational drive from the gearbox speedometer take-off to the speedometer head in the instrument panel. An inner...

Front Exhaust Pipe - downpipe section of the exhaust system. Connects the exhaust manifold to the intermediate pipe and silencer, carrying exhaust...

Steering Relay Gasket seals the steering relay assembly within the steering linkage. The steering relay transfers movement from the steering box d...

Gasket A large gasket for the 2.0L four-cylinder petrol engine. It forms a sealed joint between two mating engine components to prevent the leakag...