Products

Fuel Filler Door Latch Bezel is the trim surround that locates and frames the fuel filler flap latch within the fuel filler housing. It seats in t...

Fuel Filler Bezel - trim bezel for the fuel filler door. Surrounds the fuel filler recess, providing a finished trim edge around the fuel tank fil...

Radiator Grille Frame - With Air Conditioning for the Defender. Structural front-end panel that carries the radiator grille and defines the air in...

Bulkhead Vent - Open - LH - the left-hand (near side) hinged vent lid set into the bulkhead, forming part of the fresh-air ventilation system. Whe...

Bulkhead Vent - Open - RH - the right-hand (off side) hinged vent lid set into the bulkhead, forming part of the fresh-air ventilation system. Whe...

Boot Centre Floor Panel is a rear body repair panel forming the centre section of the boot floor within the rear load area structure. It is a stru...

Middle Floor Crossmember, a transverse structural member beneath the floor pan. This crossmember runs across the underside of the body in the midd...

Bonnet Release Cable transmits the pull from the interior bonnet release lever to the bonnet latch. Operating the cabin release lever draws the ca...

Bonnet Release Cable is the Bowden control cable that links the in-cab release lever to the bonnet latch mechanism. Pulling the release lever draw...

Floor Panel - Rear - RH for the right-hand side of the rear load area. This pressed steel body repair panel forms the right-hand inner bodyside se...

Floor Panel - Rear - LH for the left-hand side of the rear load area. This pressed steel body repair panel forms the left-hand inner bodyside sect...

Glass Channel - window glass guide channel for the rear side door. Guides and locates the door glass as it is raised and lowered, supporting smoot...

Gas Strut - Tailgate Gas-charged support strut for the rear tailgate. The strut mounts between the body aperture and the inner tailgate, using com...

Bonnet Assembly - the hinged body panel that closes over the engine compartment, forming part of the front body structure. It pivots on the bonnet...

Bonnet Stay Bracket - mounting bracket for the bonnet stay. Locates and supports the bonnet stay, holding the bonnet in the open position for engi...

Bonnet Stay Bracket is the left-hand mounting bracket for the bonnet stay. It forms the pivot-bush end of the bonnet stay assembly, providing the ...

Sill Panel Stay is a support bracket for the sill (rocker) panel. Forming part of the sill panel assembly, it braces the sill panel to the body st...

Alpine Light Weatherstrip for the right-hand side, sealing the fixed alpine light glass into the rear roof aperture of the body. The rubber weathe...

Alpine Light Weatherstrip is the moulded rubber seal that retains the left-hand alpine light glass in its roof aperture. The alpine lights are the...

Windscreen Finisher - Lower Lower windscreen finisher trim for the base of the windscreen. The finisher fits across the lower edge of the windscre...

Air Intake Finisher is the wing-top grille that covers the cold air intake aperture of the induction system. This is the right-hand wing-top finis...

Air Intake Grille is the louvred wing-top panel that covers the cold-air inlet at the base of the windscreen. Mounted on the left-hand wing top, i...

Air Intake Blanking Plate closes off the right-hand wing-top air-intake aperture where a cold-air inlet is not required. It fits the same opening ...

Air Intake Blanking Plate closes off a wing-top air intake aperture in the induction system. This is the left-hand wing-top blank for left-hand-dr...

Radio Cassette Housing for the Defender 90/110 dashboard interior trim assembly. This moulded trim housing surrounds and retains the radio cassett...

Rear Bumper End Cap - RH is the right-hand rear bumper corner cap, the moulded end section that finishes the outer corner of the rear bumper where ...

Rear Bumper End Cap - LH is the left-hand rear bumper corner cap, the moulded end section that finishes the outer corner of the rear bumper where i...

Bonnet Insulation Pad for the engine bay sound-and-heat insulation system. Fits to the underside of the bonnet, where it dampens engine noise tran...

Retaining Clip for the windscreen A-post finisher on the Discovery 2. This clip secures the interior A-post trim finisher strip to the body at the...

High-Mounted Stop Lamp Stud is a mounting stud for the high-level stop lamp. It secures the high-level (centre) stop lamp to its mounting point on...

Seat Squab is the backrest section of the right-hand front seat assembly. The squab forms the upright cushion against which the occupant's back re...

Seat Base Cushion - Front for the front seat assembly. This cushion forms the lower seating surface and mounts onto the front seat frame, supporti...

Air Conditioning Condenser - part of the air conditioning refrigerant circuit, mounted at the front of the vehicle in the airflow path ahead of the...

Instrument Panel Finisher is the moulded trim panel that frames the instrument binnacle on the dashboard. It fits over the facia around the instru...

Facia Finisher (RHD) - the trim finisher strip that runs along the top of the dashboard facia, from the instrument binnacle across to the passenger...

Heater Hose - Inlet for the engine coolant and cabin heater circuit on the Td5 2.5L 5-cylinder turbo diesel. Carries hot coolant from the engine f...

Heater Hose is a coolant hose in the heater circuit of the Td5 2.5L 5-cylinder turbo diesel. It carries engine coolant between the cooling system ...

Special Fixing Washer for the hardtop side-frame mounting. Seats over the M8 side-frame mounting stud and under its securing nut, spreading the cl...

Bulkhead Mounting Bolt - M12 x 180mm fastener securing the lower bulkhead to the chassis. Forms part of the body-to-chassis mounting at the base o...

Mounting Stud is a threaded fixing used in the rear body upper fixings. It is an M8 stud, 67 mm in length, providing a fixed threaded mounting poi...

Body Panel Stud is a threaded fixing used in the cab and rear body panel mounting hardware. It provides a fixed anchor point for securing body pan...

Screw - No. 10 x 1 in. Secures the instrument binnacle cowl and interior air-deflector trim. Sized for self-tapping installation into moulded trim...

Bush is a body mounting bush used in the rear body upper fixings. It fits at the fixing point between the body and its mounting, setting the corre...