Products

Swivel Ball Seal Retainer for the front axle swivel housing. This retaining ring clamps the swivel housing oil seal against the swivel ball, holdi...

Timing Chain Idler Wheel runs against the timing chain within the front timing case, guiding the chain and helping maintain its tension between the...

Drain plug

Gearbox Mainshaft Oil Seal for the rear of the manual gearbox, sealing the mainshaft where it passes through the rear of the mainshaft-and-gears se...

Differential flange 4-spline

Hub Oil Seal seals the rear hub assembly, retaining lubricant within the hub and excluding dirt and moisture from the wheel bearings. It runs on t...

Rear Shackle Pin for the rear leaf spring shackle. The pin secures the spring shackle at the rear mounting of the rear leaf spring, allowing the s...

Brake Shoe Anchor Plate for the rear drum brake assembly. The anchor plate provides the fixed abutment and locating point for the brake shoes. It ...

Lock Plate for the rear drum brake shoe retainer. This fold-over tab plate locks the two screws that secure the brake shoe bottom retainer ring. I...

Check Strap for the rear suspension assembly. The check strap limits the downward travel of the axle on droop, preventing the leaf springs from ove...

Bolt - 5/16 inch BSF x 1 inch for the gearbox selector assembly. Used to secure the gear selector forks to their respective selector shafts within...

Bolt - 3/8" BSF x 1" hexagonal head bolt to British Standard Fine thread specification. 3/8" BSF (British Standard Fine) thread with a 1" shank le...

Layshaft Split Ring Halves are a matched pair of semi-circular retaining ring halves used in the Land Rover Series I and II gearbox assembly. The ...

Split Pin locks slotted nuts, clevis pins and linkage joints against loosening, passing through a drilled hole and splayed to retain the assembly. ...

Exhaust Clamp Plate for the exhaust mounting assembly. Three-hole clamping plate that secures the exhaust pipe within the mounting bracket assembl...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Exhaust Clamp for the exhaust-to-chassis mounting. Two-bolt upper clamp plate that forms the exhaust-to-chassis mounting assembly on Series and ea...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Exhaust Saddle Clamp for securing exhaust pipe sections to underbody mounting brackets in the exhaust system. The U-shaped saddle body seats over ...

Clutch Anchor Plate - a steel mounting plate within the clutch pedal box assembly. It anchors the clutch pedal pivot to the bulkhead, providing th...

Axle Bump Stop - rubber bump stop for the front and rear suspension axle assemblies. Fitted to the chassis above each axle, the bump stop limits a...

Master Cylinder for the hydraulic brake circuit on early Series I Land Rovers. The master cylinder converts mechanical pedal force into hydraulic p...

U-Bolt - a rear leaf-spring axle clamp. It passes around the axle tube and clamps the rear leaf spring to the axle seat via the lower spring plate...

Front Towing Eye / Lifting Ring bolts to the front of the chassis, providing an anchored attachment point for towing, recovery and lifting. The ri...

Stub Shaft with a 10-spline drive coupling, a component of the axle half-shaft assembly. The stub shaft sits within the axle and transmits drive t...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Plain Washer - the upper mounting washer for the shock absorber. It seats over the top shock absorber mounting stud beneath the retaining nut, spr...

Front Spring Dowel for the 9-leaf front road spring, part of the leaf spring suspension assembly. The dowel is the centre locating pin that passes...

Wheel Cylinder for the drum brake assembly - the right-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either...

Wheel Cylinder for the drum brake assembly - the left-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either ...

Wheel Cylinder for the rear drum brake assembly, right-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hy...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Spring Clip - a retaining clip in the transfer gearbox selector linkage. It secures the transfer lever to its pivot, holding the gear-change lever...

Front left-hand wheel cylinder for the hydraulic front braking system, installed within the brake backplate assembly of 11-inch front brake configu...

Front brake wheel cylinder designed for use on Land Rover Series I, Series II, and Series III models. This component forms part of the hydraulic dr...

Copper Joint Washer for sealing fluid-carrying connections in the engine and cooling system. The annealed copper construction deforms under clampin...

Lamp Guard Distance Piece - spacer for lamp guard mounting hardware. The distance piece fits between the lamp guard frame and the light body or mo...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Outer Distance Piece for the front axle swivel pin housing. The distance piece is a spacer that sets the position of the swivel pin bearing within...

Rear Shackle Plate, part of the rear leaf spring mounting in the suspension assembly. The shackle plate forms one side of the spring shackle, link...

Exhaust Connecting Pipe is the intermediate section of the exhaust system for Series short wheelbase vehicles fitted with the 2.25L diesel engine, ...

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Gear - 2nd - Pair for the Series Land Rover four-speed main gearbox. This pair comprises the matched 2nd speed gears for both the mainshaft and th...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...

Cylinder Head Bolt - a clamping bolt securing the cylinder head to the engine block. It draws the head down onto the block to compress the head ga...

Domed Nut with a 5/16 UNF thread, a finishing fastener. The domed (acorn) form encloses the end of the stud or bolt it threads onto, protecting th...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...