Products

Manifold Stud - a mounting stud for the manifold. Threaded into the cylinder head, it locates the manifold and clamps it to the head face via its ...

Flywheel Housing Stud - a mounting stud at the flywheel housing. Threaded into the housing, it provides the fixed stud onto which the mating compo...

Copper Injector Sealing Washer in the fuel injection assembly of pre-TDi Land Rover diesel engines. This copper washer seats beneath the injector ...

Valve Stem Oil Seal fits over the inlet valve stems to limit oil consumption past the valve guides in the cylinder head. It is used on 2.25L petrol...

Small End Bush (gudgeon pin bush) for the connecting rod small end on Land Rover diesel engines. The small end bush is a precision bronze bush pre...

Rocker Shaft Bush in the cylinder head valvetrain. The bush is pressed into a rocker pedestal and provides the bearing surface that supports the r...

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Camshaft for the 2.25L 4-cylinder petrol engine valve train. Running in the cylinder block and driven from the crankshaft by the timing gear, the ...

Injector Nozzle is the atomising tip of the diesel fuel injector, sitting in the fuel injection circuit between the injector body and the combustio...

Timing Cover Mudshield is the pressed shield that fits over the timing cover at the front of the engine. It screens the timing case and front pull...

Manifold Gasket - inlet to exhaust manifold gasket for the 2.25L 4-cylinder petrol engine. On this engine, the inlet and exhaust manifolds bolt to...

Thermostat Housing Gasket in the engine cooling system. This gasket seals the thermostat housing to its mating surface on the engine, preventing c...

Water Pump Impeller in the engine cooling circuit. Pressed onto the water pump spindle and driven by the fan belt, the impeller circulates coolant...

Water Pump Gasket sealing the water pump to the engine in the cooling circuit. The 8-hole gasket matches the bolt pattern of the water pump mounti...

Heater Plug Lead in the diesel glow plug pre-heat circuit. This 10" interconnecting lead links the No.2 and No.3 heater (glow) plugs, carrying cur...

Glow Plug Lead in the diesel glow plug (heater plug) pre-heat circuit. This short 5" lead interconnects glow plugs wired in series and is not inte...

Bolt securing the gearbox to the transfer box in the drivetrain. This fixing clamps the main gearbox housing to the transfer box. It applies to th...

Lock Nut with a 5/16" BSF thread. The lock nut secures a threaded fastening against loosening under vibration, maintaining clamp load in service. ...

Lock nut 3/8" BSF

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Exhaust Clamp for 65mm diameter exhaust pipe sections. Used to join and secure exhaust pipe connections at joints in the exhaust system. The 65mm ...

Nyloc Nut - 9/16" UNF for use in the leaf spring suspension assembly. This self-locking nut secures the shackle pin at the rear leaf spring shackl...

Screw - 10 UNF x 3/8 is a fixing in No.10 UNF (Unified National Fine) thread, 3/8 inch in length, used in fascia and dash assembly applications. Fi...

Starter Brush Set A set of replacement carbon brushes for the starter motor, part of the engine starting circuit. The brushes bear on the commutat...

Gasket

Steering Box Joint Washer - 0.005" selective shim washer used within the steering box. Fitted at the steering box joint face, this shim sets the c...

Layshaft Sleeve - bearing sleeve fitted to the layshaft (countershaft) in the LT67 main gearbox. Provides the running surface for the layshaft clu...

Exhaust Bracket Saddle Clamp for the intermediate exhaust pipe on 109-inch wheelbase Series 2 and Series 3 Land Rovers. The saddle clamp locates an...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Wheel Cylinder Repair Kit A seal repair kit for overhauling the rear brake wheel cylinders, part of the drum braking system. The wheel cylinder si...

Clutch Slave Cylinder for the hydraulic clutch actuation system. Mounted on the gearbox bellhousing, this cylinder receives hydraulic pressure fro...

Transfer Box Sealing Ring - Locking Pin A rubber O-ring that seals the locking pin where it enters the transfer box case. It seals the selector lo...

Spring - Timing Ratchet sits within the engine timing assembly on Land Rover 2.25L and 2.0L diesel engines. This spring provides the retention for...

Thrust Washer - 0.128" A gearbox mainshaft thrust washer for the second-speed gear, 0.128" thick. It controls the end-float of the 2nd-speed gear ...

Sump Gasket seals the joint between the oil sump and the cylinder block within the engine lubrication system, preventing oil leakage at the sump fl...

Joint Washer for the LT76 manual gearbox. Fitted between mating faces within the gearbox to form an oil-tight joint on assembly. Supplied as a sin...

Sealing ring

Radiator Hose serves as the lower radiator hose in the cooling system of Series I Land Rovers built between 1948 and 1958. This hose connects the ...

Valve Cup for the valve gear of the 3-bearing 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The cup seats on the top ...

Valve Collet for the valve gear of the 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The split collets seat in the gr...

Gerschikt voor 2.25 ltr benzine

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Track Rod Assembly - 111 cm is the front axle track rod for Series II Land Rovers, connecting the two front steering knuckles to maintain correct t...

Oil Filter Bowl Bolt Washer - rubber sealing washer for the oil filter bowl centre bolt. Fitted to the centre bolt that retains the oil filter bow...

Water Pump - 2.0 IOE - the engine coolant pump in the cooling system, for the 2.0L IOE (inlet-over-exhaust) petrol engine. Driven by the fan belt ...

Lock Washer is a folding lock tab used in the front axle swivel pin housing assembly. Fitted beneath a 3/8" stud fixing, the tab is bent up agains...