Products

Shackle plate

Shackle pin

O-Ring Seal - sealing ring for the steering box rocker shaft. Fitted around the rocker (sector) shaft where it passes through the steering box hou...

Ball Race - Steering Box (Adjusting) is a component of the recirculating-ball manual steering box assembly, used to control pre-load and end-float ...

Engine Mounting Bracket for the left-hand side of the engine, part of the engine mounting system. The bracket bolts to the left-hand side of the c...

Engine Mounting Bracket - right-hand front engine mount angle adaptor. Bolts to the right-hand side of the cylinder block and carries the rubber e...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Pedal Shaft is the transverse shaft on which both the clutch pedal and brake pedal are mounted within the cab, on vehicles without a brake servo. ...

Exhaust Rocker Shaft is the shaft on which the exhaust rocker arms are mounted within the cylinder head valve train of the 2.6L 6-cylinder petrol e...

Banjo bolt

Manifold Gasket for the 2.25L and 2.5L 4-cylinder petrol engines. This gasket seals the combined inlet and exhaust manifold assembly to the cylind...

Cylinder Head Gasket - non-adhesive type, for the 2.25-litre petrol engine. Seals the joint between the cylinder head and the cylinder block, cont...

Handbrake Drum is the drum for the transmission-mounted parking brake, for use with the LT76 gearbox. Mounted at the rear of the gearbox on the tr...

Valve Rocker for the Land Rover 2.25L four-cylinder diesel engine - right-hand exhaust rocker arm. Pivots on the rocker shaft in the cylinder head ...

Rocker Cover Gasket for the 2.6L six-cylinder petrol engine, sealing the side rocker cover to the cylinder head. It forms the oil-tight joint alon...

Exhaust Packing Plate for the exhaust mounting strap assembly. It sits between the exhaust strap and its chassis bracket, packing the joint so the...

Clevis Fork is the forked end fitting used in the handbrake actuation linkage. It joins the handbrake rod to the operating lever, with a clevis pi...

Timing Chain Vibration Damper for the front timing chain drive on four- and six-cylinder engines. Mounted within the timing cover, it bears agains...

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

Oil Feed Pipe is the external oil feed pipe supplying the cylinder head within the engine lubrication system. It carries pressurised oil from the ...

Wheel Cylinder Repair Kit for overhauling a front drum-brake wheel cylinder with a 1.25 inch bore. It restores the hydraulic seal of a worn or lea...

Exhaust Pipe - Intermediate - Non-Station Wagon

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Swivel Housing Gaiter Kit in leather for the front axle swivel housings, supplied as an axle set to cover both sides. The gaiter encloses the swiv...

Swivel Housing to Stub Axle Joint Washer for the front axle swivel assembly. This sealing washer fits between the swivel housing and the stub axle...

Lock Plate for the front axle assembly. This metal tab washer locks fastener heads in position by bending a tab against the bolt head or nut after...

Timing Chain Tensioner maintains correct tension on the timing chain within the engine timing case, preventing chain slap and ensuring accurate val...

Threaded Core Plug seals a threaded aperture in the engine block casting, used on the 4-cylinder petrol engine as a blanking plug for a redundant h...

Accelerator Spring for the throttle linkage on diesel engines. This return spring acts on the accelerator linkage, drawing the throttle back to th...

Carburettor Spacer for the petrol engine induction system, fitting between the carburettor and the inlet manifold. It sets the carburettor off the...

Carburettor Manifold Gasket for the 2.25L petrol and carburettor-equipped Defender engines. This gasket seals at the interface between the carbure...

Brake & Clutch Pedal Pad for the foot pedal assembly. This moulded rubber pad fits over the brake and clutch pedal arm, providing the grip surf...

Shackle Plate for the rear leaf spring suspension, forming one half of the spring shackle assembly. The plate works together with the shackle pins...

Nut with a 5/16 inch BSF (British Standard Fine) thread. A hexagonal fastener that threads onto a matching 5/16 inch BSF bolt or stud to secure a ...

Brake Rear Drum Sprite 1-3 & Midget 1&2

Main Switch - heavy-duty main electrical switch rated at 1000A. Switches the primary high-current circuit, suited to continuous heavy-duty loads.

Cigarette Lighter Socket for the 12V auxiliary power circuit, providing a dashboard power outlet that accepts the lighter element and standard acce...

Trailer Plug - 7-Pin - 24V

Bonnet Canvas Rest Strip for the front body assembly. This canvas strip mounts across the top of the radiator/front panel, forming the surface the ...

Cleat Rope Hook Body Side All and Classic (Softtop) - Series Defender

Gear Lever Gaiter for the transmission tunnel. This flexible boot fits around the base of the gear lever where it passes through the tunnel, sealin...

Weatherstrip for the alpine light (side roof window) glass. This rubber sealing strip retains and seals the 5mm glass panels of the alpine lights ...

Gaiter Retainer - secures the rubber gaiter around the high-low (transfer) lever on the LT76 gearbox, which carries an integral transfer box. The ...