Products

Cab Body Panel Mounting Bracket - a body bracket that locates and secures a cab panel to the surrounding body structure. It provides the fixing po...

Bolt securing the bulkhead to the chassis outrigger. A 1/2" UNF hex-head bolt used at the lower bulkhead mounting points, where the bulkhead fixes...

Windscreen Glass - replacement glass panel for the windscreen frame. Fits the windscreen aperture as a direct replacement for cracked or damaged g...

Door Bottom for the left-hand side, forming the lower section of the door assembly. This is a repair panel that replaces the lower portion of the ...

Rear Sill Panel for the right-hand side, a body repair panel in the lower bodyside and chassis structure. The panel forms the rear section of the ...

Rear Sill Panel - Left Hand is a pressed steel body panel that forms the lower left-hand side of the rear body tub. The panel closes the gap betwe...

Front Sill Panel for the right-hand side, of the narrow sill type. The sill is the structural panel running along the lower edge of the body benea...

Front Sill Panel - Left Hand is a pressed steel body panel that forms the lower left-hand side of the front body section. The panel closes the low...

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Bonnet Spring Retaining Clip, part of the bonnet hinge and stay assembly. Retains the bonnet (hood) tension spring against its anchor, holding the...

Side Panel Buffer, a rubber buffer fitted at the rear body side panels. Sits between the upper and lower rear quarter panels, cushioning the joint...

Mounting stud

Handbrake Gaiter for the L-shaped handbrake lever on late Series IIA and all Series III models. Fits the oval aperture through which the lever pass...

Transfer Gear Lever Gaiter for the high/low ratio selector lever on the Series Land Rover transfer box. This rubber gaiter seals around the transf...

Rubber Washer - Window Catch for the sliding window catch assembly on Series II, IIA, and III Station Wagon body variants, produced up to 1984. Th...

Seat Belt Bracket for the front seat belt, lower mounting, left-hand side. This bracket bolts to the seat box and provides the lower anchorage poi...

Door lock RH

Door Latch Assembly - LH - Front - Non-Locking for Land Rover Series vehicles from 1958 to 1984. This left-hand front door latch assembly fits the...

Door Lock Button - LH - Push & Twist for Land Rover Series vehicles from 1954 to 1981. This left-hand push-and-twist door lock button fits the...

Spare Wheel Bonnet Strap, the retaining strap for a bonnet-mounted spare wheel. Secures the spare wheel in the bonnet-top carrying position, holdi...

Interior Mirror for Series Land Rover models. Direct-fit interior rear-view mirror providing rearward visibility from the driver's position inside...

Headlamp Bezel is the outer retaining surround for the headlamp unit, mounting within the front lighting panel. It secures and finishes the lamp a...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Rope Hook

Headlamp Guard in galvanised steel. A protective grille fitted over the headlamp lens to shield it from stone chips, debris and impact damage. The...

Headlamp Guard in moulded plastic. A protective guard fitted over the headlamp lens to shield it from stone chips, debris and impact damage. Suppl...

Squab - 1/2 Ton

Radiator Grille mounts in the front body panel aperture, ahead of the radiator, admitting cooling airflow to the core while protecting it from road...

Air Vent Mechanism - operating mechanism for the dash-mounted fresh-air ventilator. Controls the opening and closing of the bulkhead air vent flap...

Dashboard Assembly Plate is a structural panel within the facia assembly, forming the mounting base onto which the instrument panel and dashboard t...

Decal – Dash is an adhesive instrument switch-tab label for the dashboard control panel. It is applied to the face of a plastic switch tab to iden...

Demister Tube Grommet is a moulded rubber grommet in the windscreen demister ducting that seals the demister hose where it passes through the lower...

Instrument Cover is the trim cover for the instrument pack within the facia assembly, enclosing the main gauge cluster. It is also used as the cov...

Bonnet Hinge Bush for the Land Rover bonnet hinge assembly. This bush fits into the bore of the bonnet hinge, providing a wear surface around the ...

Door Check Arm Bracket is the pivot bracket in the door check assembly that anchors the check arm to the body at the rear door. The check arm runs...

Heater Air Intake Trim fits the front wing air intake of the heating and ventilation system. It finishes the fresh-air intake aperture in the wing...

Blanking Plate for the pedal box aperture, used to close off the pedal hole in the bulkhead where a pedal is not fitted. It covers the opening tha...

Rear Sill Panel for the right-hand side of the body understructure on long wheelbase (109 inch) models. Fitted at the rear sill position, this pane...

Sliding Window Catch for the front door sliding window assembly on Series Land Rover models. This black plastic catch secures the sliding window p...

Door Hinge Shim for the Land Rover door hinge assembly. This 1mm shim is fitted between the door hinge and its mounting face to set or adjust the ...

Bracket

Replace or upgrade the front outer wing panel on your Series 2/3 Land Rover with this aluminium panel designed for Right-Hand Side (RHS) and Left-H...

Outer Wing Panel for the left-hand side, manufactured in aluminium. The outer wing forms the front body panel covering the wheel arch and bolts to...

Window Channel - Lower is the lower glass-run channel for the front door window. It runs along the bottom of the window aperture and guides the do...

Window Channel, 26.5 in (673 mm), a felt-lined glass run channel for the rear body side sliding windows. The glass slides within the channel, whic...

Window Catch Gasket seals the window catch on the rear side door. It fits between the window catch and the door panel, forming a weatherproof seal...

Steering Column Cover is the upper shroud enclosing the steering column. Fits together with the lower shroud 347558 to conceal the column and swit...