Products

Intake Hose Range Rover Classic MA>, MA> - EFI Discovery 1

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

Fuel Filter

Plenum to Water Jacket Gasket seals the joint between the plenum chamber and the water-jacketed intake manifold in the Rover V8 EFI induction syste...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Trim Clip Fir-tree interior trim fastener. The ribbed fir-tree stem pushes into a panel hole to retain interior trim.

Handbrake Gaiter in Dark Granite, part of the centre console trim. This gaiter fits around the base of the handbrake lever, concealing the lever me...

Hex Flange Nut - a flanged hexagonal nut used as a general threaded fastener across multiple vehicle assemblies. The integral flange spreads the c...

Bonnet Latch Assembly for vehicles equipped with the anti-theft alarm system. This latch secures the bonnet in the closed position and incorporates...

Front Door Lock Assembly for the right-hand front door, right-hand drive configuration. This assembly secures the door to the body striker and con...

Front Door Latch Assembly for the left-hand front door latching system. The assembly houses the latch mechanism that engages the striker on the bo...

Tailgate Latch Assembly is the lower tailgate latch mechanism, fitted at the centre of the lower tailgate. It secures the lower tailgate closed an...

Clevis pin

Differential Thrust Washer for the four-pinion differential in the Land Rover-type axle. Seats behind a differential gear to control end-float and...

Fixing Screw used in the flywheel, drive plate and clutch assembly. It is one of the threaded fasteners securing the flywheel or automatic drive p...

Bonnet Release Latch

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Reverse Idler Shaft for the R380 5-speed manual gearbox. The shaft carries the reverse idler gear within the gearbox casing. The reverse idler gea...

Level plug R380

Front Driveshaft Oil Seal located at the differential housing output in the Front Axle Assembly, sealing around the front halfshaft where it exits ...

Layshaft is the countershaft within the R380 five-speed manual gearbox, carrying the cluster of gears that mesh with the mainshaft gears. Drive pa...

Oil Feed Ring - mainshaft oil feed ring for the R380 five-speed manual gearbox. Located on the gearbox mainshaft, it channels lubricating oil to t...

Handbrake Shoe Kit - the retention (hold-down) hardware for the transmission handbrake, which acts on the LT230 transfer box rather than at the roa...

Gearbox Mount Assembly is the transmission mounting that supports the rear of the gearbox on the gearbox crossmember. It carries the weight of the...

Cylinder Head Bolt Kit is a complete set of the bolts that clamp the cylinder head to the engine block. The kit comprises 14 Torx-drive cylinder h...

Crankshaft Pulley - for the 4.0L and 4.6L V8 EFI petrol engine. Mounts to the nose of the crankshaft at the front of the engine and drives the acc...

Sensor

Kit - Caliper Brake Pad

Rocker Cover Gasket for the Rover V8 petrol engine, sealing the rocker (valve) cover to the cylinder head. The gasket seats between the cover flan...

Sump Gasket for the Rover V8 4.0 and 4.6 petrol engine, sealing the oil sump to the underside of the cylinder block. This is the one-piece rubber-...

Flanged Hex Bolt securing the lower inlet manifold on the V8 EFI petrol engine. The integral flange under the head spreads the clamping load acros...

Inlet Manifold Insert - press-in insert that forms the vacuum take-off union in the upper inlet manifold. The insert is pressed into a machined bo...

Sealing Washer - 18 mm OD x 12 mm ID is a sealing washer with a 12 mm inner diameter and an 18 mm outer diameter, used to seal threaded unions and ...

Throttle body heater plate for the 4.0L and 4.6L EFi Rover V8 petrol engine, fitted to the underside of the throttle body. The plate carries engin...