for Discounts / VAT
for Discounts & Correct VAT
Oil cooler seal, 18 mm diameter, sealing an oil transfer connection between the engine and the oil filter housing on the 3.0L V6 diesel. Three are...
View full detailsOil cooler seal, 9.5 mm diameter, sealing the small-bore oil transfer connection between the engine and the oil filter housing on the 3.0L V6 diese...
View full detailsWater pump for the 3.0L V6 diesel (TDV6 / SDV6). It drives coolant circulation through the cylinder block and heads, out through the radiator circu...
View full detailsCoolant Pipe - Lower Radiator is a connector tube in the bottom radiator hose run of the engine cooling system. It joins two sections of the lower...
View full detailsTurbo Oil Return Hose Gasket seals the upper joint of the turbocharger oil return hose, where the hose meets the turbocharger housing in the engine...
View full detailsTiming Gear Bolt - Lower is the M16 x 70mm flanged hex bolt that retains the lower timing gear on the crankshaft. It is also listed as the cranksha...
View full detailsOil Separator Pipe for the 3.0L V6 diesel engine, forming part of the crankcase emission control (crankcase ventilation) system. It carries blow-b...
View full detailsOil Separator Reservoir for the 3.0L V6 diesel, part of the crankcase ventilation circuit within the engine emission control system. Crankcase blo...
View full detailsCrankcase Ventilation Tube for the 3.0L V6 turbo diesel engine, part of the oil pan and crankcase breather arrangement. Combustion gases that leak...
View full detailsFuel Filler Restrictor for diesel vehicles, fitted inside the fuel filler neck as part of the fuel tank and filler assembly. It forms a physical b...
View full detailsSpark Plug Aperture Gasket seals the spark plug aperture in the cylinder head cover on the left hand cylinder bank. It closes the joint between th...
View full detailsExterior mirror motor - left-hand side glass adjustment motor within the door mirror head. The motor sits behind the mirror glass and drives the g...
View full detailsBrake Disc - front axle, internally vented. The disc provides the friction surface that the front brake pads clamp against, converting the vehicle...
View full detailsExhaust downpipe gasket sealing the flanged joint between the front exhaust pipe (downpipe) and the catalytic converter, in the front section of th...
View full detailsExhaust downpipe gasket sealing the flanged joint between the front exhaust pipe (downpipe) and the catalytic converter, in the front section of th...
View full detailsFront timing belt kit for the 2.7L and 3.0L V6 turbo diesel engine - the lower belt of the camshaft timing drive. The belt is driven from the cran...
View full detailsRear timing belt kit - fuel injection pump drive for the 3.0L V6 turbo diesel engine. The rear belt drives the high-pressure fuel injection pump a...
View full detailsFront Brake Caliper Attachment Kit supplying the pad-retaining and caliper attachment hardware that secures the brake pads in the front caliper bod...
View full detailsInjector Refit Kit - Cylinder No.1 supplies the parts renewed when a fuel injector is removed and refitted, within the fuel injectors and pipes ass...
View full detailsKit - Injector Refit
Injector Refit Kit - Cylinders No.3 and No.4 supplies the parts renewed when a fuel injector is removed and refitted, within the fuel injectors and...
View full detailsClip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.
Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...
View full detailsWater Outlet Tube for the engine cooling circuit of the naturally aspirated 5.0L AJ133 V8 petrol engine. The tube carries coolant between the wate...
View full detailsBrake Disc Retaining Screw that locates the brake disc against the wheel hub flange, holding the disc square and in position while the caliper and ...
View full detailsThermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...
View full detailsCamshaft Screw for the cylinder head and camshaft assembly of the 3.0-litre TDV6 diesel engine. This is a manufacturer-specification retaining scr...
View full detailsManifold Absolute Pressure (MAP) Sensor for the 3.0L V6 diesel engine. Mounted on the throttle housing, it measures the absolute pressure in the i...
View full detailsFlanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...
View full detailsOil Filter Housing Cover is the cover for the cartridge-type oil filter assembly on 3.0 GDI petrol and 5.0 AJ-V8 engines. This cover retains the r...
View full detailsAxle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...
View full detailsEGR Gasket Inlet
EGR Tube connecting the exhaust manifold to the EGR valve on the 3.0L V6 turbo diesel engine. Carries hot exhaust gas from the exhaust manifold to...
View full detailsEGR Tube connecting the exhaust manifold to the EGR valve on the 3.0L V6 turbo diesel engine. Carries hot exhaust gas from the exhaust manifold to...
View full detailsThrottle Body for the air intake system of the 4.4L V8 diesel engine. The electronically actuated throttle valve regulates intake airflow into the...
View full detailsFuel Return Pipe for the diesel fuel system return circuit, 3.0L V6 diesel applications. The return pipe carries surplus fuel not consumed by the ...
View full detailsWater Pump for the 4.4L DOHC V8 turbo-diesel (TDV8) engine. It circulates coolant through the engine block, cylinder heads and radiator to maintain...
View full detailsEGR Cooler Inlet Hose for the 4.4L DOHC V8 turbo-diesel (TDV8) engine. It routes engine coolant to the exhaust gas recirculation (EGR) cooler, whic...
View full detailsEGR Cooler Outlet Hose for the 4.4L DOHC V8 turbo-diesel (TDV8) engine. It returns engine coolant from the exhaust gas recirculation (EGR) cooler t...
View full detailsExhaust Manifold Gasket for the 4.4L DOHC V8 turbo-diesel (TDV8) engine. It seals the joint between the exhaust crossover pipe and the exhaust mani...
View full detailsCoolant Hose forms part of the heater line within the engine cooling system, routing coolant between the engine and the heater matrix. Supplied co...
View full detailsTurbocharger Oil Return Tube Gasket seals the oil return (drain) tube where it meets the turbocharger, within the turbocharger lubrication circuit....
View full detailsOil Separator Reservoir forms part of the crankcase emission control (crankcase ventilation) system. It separates entrained engine oil from crankc...
View full detailsEGR Outlet Gasket for the exhaust gas recirculation (EGR) system on the 4.4L DOHC DITC V8 diesel engine. Seals the joint between the EGR valve out...
View full detailsEGR Inlet Gasket for the 4.4L DOHC V8 turbo-diesel engine, part of the exhaust gas recirculation (EGR) system. It forms the gas-tight joint where ...
View full detailsTensioner - Drive Belt
Exhaust Gas Temperature Sensor for the diesel particulate filter (DPF) system. Monitors exhaust gas temperature in the after-treatment section and...
View full detailsFilter - Oil - Element and Seal