Products

Strap

Key Blank for Land Rover lock barrel assemblies. This uncut key blank matches the barrel profile used in door locks, ignition locks, the tailgate, ...

Gearbox Reverse Stop Adjuster screw, part of the reverse gate mechanism in the manual gearbox gear-selection assembly. It sets and limits the gear...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Mudguard - Power Take Off for the centre power take-off (PTO) housing. Mounted to shield the centre PTO unit from mud, water and road debris. Prot...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Oil Pump Sealing Washer, part of the engine lubrication circuit at the oil pump. The washer forms a static seal at the oil pump joint, preventing ...

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Special Bolt with a coarse ACME-form thread, 1/4 in diameter and 5/8 in long. It is a body fixing used to secure inner-wing mudshields, floor plat...

Plain Washer - 7/16" used in the power steering box assembly. This flat washer is used within the steering hydraulic assembly at the power steerin...

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Clip - a retaining clip within the vehicle body hardware, used to secure and locate a fitted component in position.

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Bush

Bonnet Catch, the bonnet safety catch assembly mounted at the front of the engine bay. It engages the bonnet as a secondary retention after the pr...

Grommet fits the bonnet release and locking mechanism. It lines the panel aperture through which the bonnet release cable passes, sealing the open...

Fuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...

Side Window Insert Spring Tensioning spring for the sliding side window insert in the two-door body's side window assembly. It provides the retain...

bracket 390384

Dash Assembly Bracket - a structural support bracket forming part of the dashboard (fascia) assembly. The bracket provides a fixing point within t...

Interior Door Pull Handle for the front right-hand door of the Range Rover Classic 2-Door Station Wagon. This is the inner grab handle mounted on ...

Glovebox Lock Set secures the glovebox lid in the closed position and is released by key. It mounts in the glovebox within the facia, forming part ...

Rear Mudflap Mounting Angle, the angled bracket that secures a rear mudflap to the underbody. It positions and supports the mudflap behind the rea...

Wing Seal A rubber sealing strip fitted to the inner wing. It seals the joint at the wheelarch and valance to keep out water and road debris.

Rear Window Sealing Pad for the Range Rover Classic. This rubber pad seals the rear side window aperture, preventing water ingress and wind noise ...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Cap Reservoir Br.m.cylinder

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...