Products

Differential Shim - 0.072in, for the Rover-type differential. Fitted during differential setup to set bearing preload and gear alignment. Shim thi...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Differential Shim - 0.048in. Fitted during differential assembly to set bearing preload and gear alignment. Shim thickness is selected against mea...

Differential Shim for the crownwheel and pinion assembly. Fitted during differential assembly to set bearing preload and gear alignment. Shim thic...

Differential Pinion Shim - 0.052in. Fitted between the pinion head and its bearing to set pinion depth and preload during differential setup. Shim...

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Clutch Cap that closes an aperture in the clutch bellhousing around the release mechanism. Fitted over an opening in the bellhousing, the cap seal...

M6 Stud for the gearbox main casing. This threaded stud secures the speedometer drive housing to the transmission main casing, providing the fixin...

Washer

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Brake & Clutch Pedal Bush for the pedal box assembly. It forms the pivot bearing where the pedals mount on their shaft, locating the brake and ...

Shim bearing differential 0.062""

Shim 1.65mm for Layshaft Speed - V8 4

Locking Washer for the swivel pin housing, fitted at the lower swivel pin. Its tab is folded against the retaining bolt to lock the fixing and prev...

Torsion Spring Sleeve for the lower tailgate. It fits over the tailgate torsion spring, forming a protective bearing sleeve at the pivot and preven...

Torsion Spring Sleeve for the lower tailgate. It fits over the tailgate torsion spring, forming a protective bearing sleeve at the pivot and preven...

Washer 577254

Spring Ring

Fuel Gauge for the dashboard instrument cluster. An analogue gauge that indicates the quantity of fuel in the tank. It responds to the variable-re...

Switch Assembly

pipe clip 1/2" (12.7mm) for 3/8" (9.5mm) hole

Wiper & Washer Switch

Inner Ring

Accelerator Pedal Lever Pad is the moulded rubber pad that fits over the accelerator pedal lever. It provides the contact face between the driver's...

Oil Shield (front hub mudshield) for the front axle hub assembly. Fitted to the front hub on the Range Rover Classic, this shield sits between the...

Blanking Plate for the inlet manifold of the 3.5L V8 twin-carburettor petrol engine. The plate closes off an unused port on the manifold to maintai...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Intake Elbow Seal for the 3.5L V8 twin-carburettor petrol engine. The seal sits between the air cleaner intake elbow and the carburettor intake to ...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Splined End

Temperature Sensor mounted in the air filter (air cleaner) housing. This thermal sensor unit sits within the air intake housing and responds to th...

GENUINE LR camshaft sprocket for Rover V8 engines