for Discounts / VAT
for Discounts & Correct VAT
Carburettor Gasket sealing the inlet manifold adaptor elbow to the carburettor on the Rover V8 twin-carburettor petrol engine. Fitted between the ...
View full detailsThermostat Housing Gasket seals the thermostat housing (water outlet elbow) to the intake manifold on the 3.5L carburettor V8 engine. It sits in t...
View full detailsCarburettor Vent Hose for venting the carburettor float chamber on the twin-carburettor induction system. The hose connects to the float chamber v...
View full detailssleeve 622538
Retaining Clip used to hold the lock barrel in place. Supplied as a single clip.
Upper Tailgate Screw, a fixing used in the upper tailgate assembly. It secures the upper tailgate components in place, providing a threaded fasten...
View full detailsSpire Nut, a J-type sheet-metal spring nut (also known as a speed nut) used to secure trim, panels and fittings. The nut clips over a panel edge o...
View full detailsNutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...
View full detailsPipe Clip, a routing clip that retains pipework and small-bore lines against the chassis, body or transmission casing. It supports breather, fuel,...
View full detailsBrake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...
View full detailsSnap Ring
Gearbox Filter Plug for the LT77 five-speed manual gearbox. The plug closes the bore in the extension case that gives access to the gearbox oil fil...
View full detailsExhaust Mounting U-Bolt used to clamp and secure the exhaust system to its mounting bracket on the Range Rover Classic. This U-bolt wraps around t...
View full detailsBolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...
View full detailsDowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...
View full detailsDowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...
View full detailsFuel Pump Gasket seals the external fuel pump to its mounting face in the fuel delivery system, preventing leakage at the joint. Used on petrol ap...
View full detailsHex Nut A 3/8 UNF hexagonal fastener used in the carburettor assembly of the 3.5L V8 petrol twin-carburettor engine. It secures components within ...
View full detailsSelf-Tapping Screw for body and trim fixing applications. Used to secure window surrounds, bodyside trim, facia and switch panels. The self-tappin...
View full detailsScrew – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...
View full detailsSelf-Tapping Screw is a fixing that secures the steering column shroud in place. Being self-tapping, it forms its own thread as it is driven, retai...
View full detailsScrew for body, trim and facia fixing applications. Used to secure roof trim, rear lamp fixings and facia rail panels. A general-purpose threaded ...
View full detailsScrew - a No. 10 x 1" pan-head self-tapping screw used across interior and door assemblies. It secures the window regulator and door glass channel...
View full detailsSelf-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...
View full detailsCable Tie for securing wiring looms and cables in Land Rover applications.
Fan Motor for the in-dash air conditioning condenser and receiver-drier assembly. The motor drives the fan that draws air across the condenser and...
View full detailsAlternator Bearing Kit for the drive end of the Lucas A133 alternator. It renews the bearing at the pulley (drive) end of the rotor shaft, which su...
View full detailsResistor Assembly sets the blower motor fan speeds within the heating and air conditioning system. Wired in series with the blower motor on the lo...
View full detailsThrottle Disc is the throttle butterfly for the Solex carburettor, operating in the air and fuel induction system. Mounted on the throttle spindle...
View full detailsScrew for the valve rocker (rocker shaft) assembly of the VM 2.4L and 2.5L 4-cylinder turbo diesel engine. Retains the rocker gear on the cylinder...
View full detailsRocker Cover O-Ring for the VM four-cylinder turbo diesel engine, sealing the rocker (cam) cover to the cylinder head. It maintains the oil-tight ...
View full detailsInjector Bush for the VM 2.4L and 2.5L 4-cylinder turbo diesel engine in the Range Rover Classic. This bush is fitted at the cylinder head to loca...
View full detailssealing washer AEU2152L
Oil Seal
Pipe Clip used to secure and route pipework such as fuel breather and roll-over anti-spill lines. The clip holds the pipe at a fixed point to prev...
View full detailsSealing Washer - a sealing washer used at cylinder head and thermostat housing joints within the cooling and lubrication circuit. Fitted beneath a...
View full detailsSwitch A facia-mounted rear fog lamp switch belonging to the auxiliary switch group. It is a push-push (latching) type switch: a first press latch...
View full detailsFacia Assembly Fastener - a fastener for mounting the facia assembly to the dash structure. It secures the facia panel in place and is also used t...
View full detailsHazard Warning Switch for the fascia switch panel. Push-push (push-on/push-off) switch that operates the hazard warning flasher circuit.
Spring Nut A clip-on spring-steel fastener, also known as a speed nut, used across body, grille and chassis fittings. It slides over a panel edge ...
View full detailsSpring Nut is a sheet-metal fastener used in body panel and interior trim assemblies. It clips over a panel edge or into a pre-formed hole to prov...
View full detailsRear Side Glass - Right-Hand for the Range Rover Classic 4 Door Station Wagon body. Fixed rear quarter window glass for the right-hand side of the...
View full detailsBattery Mounting Panel The pressed panel that forms the base on which the vehicle battery is seated and secured. It locates and supports the batte...
View full detailsCheck Strap is a front door mechanism that controls how far the door opens. Mounted between the door and the body pillar, it limits the door's swi...
View full detailsFront Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...
View full detailsDoor Glass Channel the glass run channel within the door assembly. The channel guides the door glass as it is raised and lowered by the window reg...
View full detailsWiper Linkage Joint Seal for the windscreen wiper linkage assembly. Seals the pivot joint where the wiper spindle passes through the linkage, keep...
View full detailsSwitch - Window Lift - Centre Console - Discovery 1/RRC