Products

Gasket

EGR Valve for the exhaust gas recirculation system on the 4.4L V8 petrol engine. The valve meters a controlled portion of exhaust gas from the exh...

Gasket A throttle housing gasket that seals the joint between the throttle body and the intake on the 4.4L V8 petrol engine. It seals the mating f...

Water Pump in the engine cooling circuit, for AJ-V8 4.4L and 4.2L Supercharged petrol engines. This pump circulates coolant through the engine blo...

Head Gasket - V8 - RH seals the right-hand cylinder head to the engine block on the 4.4L AJ-V8 petrol engine. It forms the gas-tight joint between...

Head Gasket - V8 - LH seals the left-hand cylinder head to the engine block on the 4.4L AJ-V8 petrol engine. It forms the gas-tight joint between ...

Exhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head within the exhaust assembly. It maintains a gas-tight s...

Inlet Manifold Gasket sealing the inlet manifold to the cylinder head on the 4.2L V8 Supercharged petrol engine. It maintains a sealed air path at...

Lower Inlet Manifold Gasket sealing the lower section of the inlet manifold assembly on the AJV8 petrol engines. It forms the joint between the lo...

Cylinder Head Gasket for the 4.2L V8 Supercharged petrol engine, sealing the cylinder head to the cylinder block. It seals the combustion chambers...

Cylinder Head Gasket - LH seals the left-hand cylinder head to the engine block on the 4.2L V8 Supercharged petrol engine. It forms the gas-tight ...

Cylinder Head Bolt - M10 x 175mm bolt clamping the cylinder head to the block on the AJ-series V8 petrol engine. A torque-to-yield fastener; twent...

Valve Cover Grommet for the AJ-V8 petrol engine. It seals the cylinder head (valve) cover where a component passes through it, preventing oil escap...

Ignition Coil for the AJ-V8 petrol engine. This coil is of the coil-on-plug type, fitted one per cylinder, mounting directly over the spark plug to...

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Floor Pan Blanking Plug. It closes an unused aperture in the floor pan, sealing the opening against water, dust and road debris.

Rear Brake Pipe Clip retains and locates the rigid brake pipes along the rear of the chassis. It holds the brake lines securely against the chassi...

Bracket - Mtg

Rubber Mount - isolating insulator in the suspension system. Cushions and locates suspension components against the chassis, damping vibration and...

Fuel Filler Door Latch Bezel is the trim surround that locates and frames the fuel filler flap latch within the fuel filler housing. It seats in t...

Bracket - Fender Mounting

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Gas Strut for the upper tailgate glass window. This gas-filled strut supports the opening rear glass of the tailgate, damping its travel and holdi...

Gas Strut for the rear tailgate, right-hand side. This gas-filled strut supports the rear tailgate, assisting it open and holding it open once rai...

Fuel Filler Door Actuator operates the fuel tank filler flap as part of the central locking system. The actuator drives the locking pin that secur...

Fuel Filler Door Latch secures the fuel tank filler flap in the closed position. The latch holds the filler door flush against the body and releas...

Fuel Filler Door Spring for the fuel filler door and controls assembly. This spring provides the return force that holds the fuel filler door in t...

Fuel Filler Door Seal is the rubber seal fitted around the fuel filler door aperture in the rear body panel. It seals the recess behind the hinged...

Exterior Rear View Mirror is a door-mounted mirror assembly within the exterior mirror and door glass group. The unit provides the driver's outwar...

Door Handle Cap - LH is the left-hand end cap for the exterior front door handle assembly, incorporating the lock barrel aperture. The cap forms t...

Door Handle Cap is the exterior end cap fitted to the right-hand-side door handle, finishing the handle end on a door without a lock barrel. It is...

Door Handle Cap is the exterior end cap fitted to the right-hand-side door handle, finishing the handle end on a door without a lock barrel. It is...

Service Kit - L405 - 3.0 V6 Die & RRS - 3.0 V6 Die - EA000001 On

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Land Rover Oval Name Badge - Plastic - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground, moulded in ...

Land Rover Grille Name Plate - Black & Silver - front grille name plate carrying the Land Rover lettering, finished in black and silver. Mount...

Oval LAND ROVER Badge - gold lettering on a green background - for the tailgate. This is the classic oval "LAND ROVER" name badge fitted to the ex...

"Land Rover" Rear Decal Badge A self-adhesive lettered name plate forming part of the exterior rear badging, applied to the rear bodywork. The let...

"TDV8" Name Plate - 9 cm engine-designation name plate identifying the TDV8 diesel V8 variant. Applied to the exterior body as an engine identifier.

Exhaust Mounting - Rubber is a rubber isolator in the exhaust suspension system, fitted between the exhaust assembly and the vehicle underbody. Th...

Wiper Arm Cap is the spindle nut cover that fits over the wiper arm pivot, concealing and protecting the retaining nut where the arm mounts to the ...