Products

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Bolt - 3/8" UNC x 1-1/4" is a UNC hex head bolt used in the front axle assembly of Land Rover vehicles. Used to secure the track rod damper bracke...

Bolt Exhaust manifold fixing bolt, 5/8" UNC x 5-1/2", for the 3.5L V8 petrol engine. Secures the exhaust manifold to the cylinder head within the ...

Bolt is a hex-head threaded fastener used to secure components at bolted joints, such as engine and starter-motor mountings.

Gas Strut for the upper tailgate glass window. This gas-filled strut supports the opening rear glass of the tailgate, damping its travel and holdi...

Gas Strut for the rear tailgate, right-hand side. This gas-filled strut supports the rear tailgate, assisting it open and holding it open once rai...

Stay Luggage compartment door stay that supports the door when open and controls its travel. Mounts between the body and the luggage compartment d...

Door Stay for the luggage compartment (lower tailgate) door. Restrains the door's opening travel and supports it in the open position, taking the l...

Door Stay for the luggage compartment (lower tailgate) door. Restrains the door's opening travel and supports it in the open position, taking the l...

Needle Valve Kit Float-chamber needle valve and seat for the Zenith Stromberg 175CD carburettor, fitted to the 3.5L V8 petrol engine. The needle v...

Piston Ring Set seals the piston within the cylinder bore as part of the engine's piston assembly, providing combustion sealing, oil control and he...

Bonnet - Less Hinges for the Defender Puma era body assembly. This bonnet panel is taller and wider than the pre-2007 Defender bonnet, with a dist...

Bonnet Stay Clip - Freelander

Clip

Fuel Filler Door Actuator operates the fuel tank filler flap as part of the central locking system. The actuator drives the locking pin that secur...

Fuel Filler Door Latch secures the fuel tank filler flap in the closed position. The latch holds the filler door flush against the body and releas...

Fuel Filler Door Spring for the fuel filler door and controls assembly. This spring provides the return force that holds the fuel filler door in t...

Hinge

Fuel Filler Latch Clip is a small retaining clip within the fuel filler flap assembly. It holds the spring-loaded latch in position inside the fil...

Radiator for the engine cooling system, fitted to the 2.5L VM four-cylinder turbo diesel. The radiator forms the heat-exchange core of the cooling...

Decal - TDi - a self-adhesive "TDi" engine decal for the front wing, in light grey and measuring 9cm. The decal reproduces the original "TDi" wing...

Decal

Decal

Front Grille Badge is the model identification badge fitted to the front grille panel. It mounts to the grille to carry the marque branding at the...

Land Rover Logo Tape - adhesive decal, 25cm length. Self-adhesive Land Rover logo tape from the Defender transfers and graphics range. Applied to ...

Body Decal reading 'Defender 110' - an exterior self-adhesive graphic finished in silver lettering on a clear backing. The decal is applied to the...

Heater Hose forming part of the cabin heater coolant circuit, carrying feed coolant from the engine cooling system to the heater matrix. For the 2...

mat BTR1194LOY

Differential Lock Instruction Label, a self-adhesive label applied to the fuse box cover showing the operating instructions for the differential lo...

Differential Lock Instruction Label, a self-adhesive label applied to the fuse box cover showing the operating instructions for the differential lo...

Clip - retaining for rubbing strip - rear quarter

Screw is a fixing screw used to secure exterior lamp, interior lamp and trim components to the body. It retains fittings such as the high-level st...

Defender 110 Decal - black, approximately 26cm length. Self-adhesive black Defender 110 model identification decal from the Defender transfers and...

Push Pin Clip plastic fir-tree fastener measuring 6.5 x 6 mm. A multi-purpose push-in retainer used to secure interior and exterior trim panels, i...

Plastic Rivet for use in the rear bumper assembly on Discovery 1. This plastic push-fit rivet secures bumper trim and moulding panels to their mou...

Rear Tread Strip protective finisher fitted to the rear end of the body, moulded in gloss black. Guards the rear sill and load-area edge against s...