Products

Heater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Bush

Retainer - Valve Spring

Bonnet Catch, the bonnet safety catch assembly mounted at the front of the engine bay. It engages the bonnet as a secondary retention after the pr...

Grommet fits the bonnet release and locking mechanism. It lines the panel aperture through which the bonnet release cable passes, sealing the open...

Interior Mirror Plate is the base/fixing plate that mounts the interior rear-view mirror to the body. It is a three-hole mounting plate that faste...

Rear Indicator Amber Lens

Fuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...

Side Window Insert Spring Tensioning spring for the sliding side window insert in the two-door body's side window assembly. It provides the retain...

bracket 390384

Dash Assembly Bracket - a structural support bracket forming part of the dashboard (fascia) assembly. The bracket provides a fixing point within t...

Interior Door Pull Handle for the front right-hand door of the Range Rover Classic 2-Door Station Wagon. This is the inner grab handle mounted on ...

Glovebox Lock Set secures the glovebox lid in the closed position and is released by key. It mounts in the glovebox within the facia, forming part ...

Rear Mudflap Mounting Angle, the angled bracket that secures a rear mudflap to the underbody. It positions and supports the mudflap behind the rea...

Wing Seal A rubber sealing strip fitted to the inner wing. It seals the joint at the wheelarch and valance to keep out water and road debris.

Rear Window Sealing Pad for the Range Rover Classic. This rubber pad seals the rear side window aperture, preventing water ingress and wind noise ...

Fuel Tank Mounting Washer is used at the fuel tank mounting points, spreading the clamping load of the fixing across the mounting bracket or strap....

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Harness Bracket Shim for the wiring harness mounting hardware. Fitted behind the harness support bracket at its mounting point, the shim sets the ...

Bump Stop for the suspension, mounted at the limit of axle travel. This rubber stop caps upward suspension movement at full compression, providing...

Screw - a threaded fastener used to join or secure components.

Door Check Strap Assembly A check strap that limits how far the side-hinged tailgate opens and holds it at its open position. Fitted to the lower ...

Coolant Outlet Gasket for the engine cooling system, sealing the coolant outlet flange where it joins the engine on V8 applications. The gasket fo...

Valve Rocker Arm operates in the cylinder head valvetrain of the 4.0L V6 Cologne SOHC petrol engine, transferring camshaft lift to the valve stem t...

Timing Gear Bolt is the hex-head flanged bolt that retains the upper timing gear on the valve-timing drive. It secures the upper gear against the ...

Timing Chain Tensioner - Lower in the timing chain drive of the AJ-V8 petrol engine (4.4L and 4.2L supercharged). It maintains correct tension on ...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Crankshaft Oil Seal – Rear seals the rear of the crankshaft where it exits the cylinder block, retaining engine oil at the crankshaft-to-transmissi...

O-Ring A 53mm-diameter sealing O-ring for the thermostat housing in the engine cooling circuit. It seals the thermostat housing joint against cool...

Thermostat Housing Seal for the engine cooling system, sealing the thermostat housing joint. Fitted between the thermostat housing and its mating ...

Timing Chain Tensioner – Balance Shaft maintains tension on the balance shaft drive chain of the 4.0L V6 Cologne SOHC petrol engine, taking up slac...

Thermostat Housing Gasket in the engine cooling system. This 37 mm gasket seals the joint between the thermostat housing and the engine on AJ-V8 4...

Oil Filter filters the engine lubrication oil on the 4.0L V6 Cologne SOHC petrol engine, removing contaminants from the oil before it returns to th...

Front Crankshaft Oil Seal for the AJV8 4.4L petrol engine, sealing the front of the crankshaft where it passes through the timing gear cover. It r...

Timing Cover Seal for the AJV8 petrol engine - a rubber seal fitted to the timing gear cover. It seals the timing gear cover against the cylinder ...