Products

Exhaust Clamp for the Puma diesel exhaust system, on installations fitted with a diesel particulate filter (DPF). The clamp joins two sections of ...

Exhaust Clamp securing a joint in the exhaust system. It clamps adjoining exhaust sections together to hold the joint tight and gas-sealed.

Door Lock Cover Plate Seal for the rear-end door latch assembly. The gasket seals the lock cover plate against the door, keeping water and dust ou...

Fuel Tank Vent Hose - part of the fuel tank ventilation circuit on Puma TDCi models. It carries fuel vapour from the tank, allowing the tank to br...

Timing Belt Kit with Water Pump for the camshaft drive of the 2.2L DOHC diesel (DW12) engine. The timing belt synchronises crankshaft and camshaft...

Bush is a rear suspension bush for the rear knuckle and suspension arm. It forms the pivoting mount between the rear suspension arm and the knuckl...

Timing Chain Lubricating Oil Jet for the timing drive of the 5.0L V8 petrol engine (AJ133, naturally aspirated and supercharged). The jet feeds pr...

Fuel Injector Sealing Washer for diesel injector installations. The washer seals the fuel injector against its seat in the cylinder head, containi...

Transmission Oil Cooler Hose for the automatic transmission fluid cooling circuit. The hose carries automatic transmission fluid between the gearb...

Door Speaker An original-fit speaker for the in-car audio system. It reproduces the audio output of the radio/head unit through the vehicle's spea...

Kit - Caliper Brake Pad

Speed Control Inhibitor Switch - a pedal-actuated switch in the cruise (speed) control circuit. Mounted at the pedal box, it signals the control m...

Brake Light Switch

Switch - Stop Light

Retaining Clip - a fastener for exterior body mouldings and side-step trim. Secures body moulding and side-step trim panels to the bodywork.

Front Door Handle Cap - a trim cap for the front exterior door handle assembly. Covers the lock mechanism aperture on the front door handle, conce...

Wiper Arm Cap - a trim cover for the windscreen wiper arm spindle. Conceals and protects the wiper arm retaining nut at the base of the front wipe...

Retaining Clip - a push-fit fastener used to secure exterior and interior trim mouldings and finishers to the body. The clip pushes into a locatin...

Differential Mounting Washer - fitted at the front differential mounting to spread the clamp load across the housing insulator bush. The washer se...

Differential Mounting Washer - fitted at the front differential mounting to spread the clamp load across the housing insulator bush. The washer se...

Ride Height Sensor - electronic air suspension height sensor. The sensor links the suspension arm to the body and continuously reports the ride he...

Ride Height Sensor - rear electronic air suspension height sensor. The sensor links the rear suspension arm to the body and continuously reports t...

Bush - front crossmember and stabiliser bar mounting insulator within the front suspension assembly. The insulator locates the front crossmember a...

Bush - front axle case mounting insulator within the front suspension assembly. The insulator isolates the front axle case from the body, absorbin...

Brake Caliper Mounting Bolt for the front brake assembly, securing the caliper to its mounting on the hub carrier. This high-tensile fastener is t...

Brake Pad Wear Warning Wire for the front brake pads, part of the brake pad wear warning circuit. The sensor wire is routed at the front brake pad...

Brake Pad Wear Warning Wire for the rear brake pads, part of the brake pad wear warning circuit. The sensor wire is routed at the rear brake pad a...

Brake Disc

Bonnet - Defender

Washer and Screw - a combined screw and washer fastener assembly supplied as a single service item.

Drive Belt Tensioner Pulley for the auxiliary drive belt system on the 2.2/2.4L TDCi diesel engine. The pulley runs against the auxiliary (poly-V)...

Steering Column Joint of double cruciform (universal joint) design, fitted in the steering column intermediate shaft. It transmits steering input ...

Thermostat for the engine cooling system on the 3.0L 24V DOHC V6 turbo diesel engine. It regulates coolant flow between the engine and radiator, s...

Exhaust Camshaft Sprocket for the valve timing drive on the 2.0L 16V TIVCT turbo petrol engine. Mounted on the exhaust camshaft, it is driven by t...

EGR Cooler Hose for the exhaust gas recirculation (EGR) circuit on the 3.0L 24V DOHC V6 turbo diesel engine. It carries engine coolant to the EGR ...

Rear Door Trim Panel is the interior casing that finishes the inside face of the rear tail door, concealing the door structure behind a moulded pan...

Water Outlet Tube carries coolant between the water pump and the thermostat housing within the engine cooling circuit. For 3.0L supercharged V6 an...

Exhaust Manifold Bolt secures the exhaust manifold to the cylinder head. For 3.0L supercharged V6 and 5.0L V8 petrol applications.

Exhaust Manifold Stud secures the exhaust manifold to the cylinder head, part of the exhaust manifold mounting hardware. This is an M10 stud, thre...

EGR Gasket for the exhaust gas recirculation (EGR) system. Seals the flanged joint between the EGR valve and its mating pipework, containing recir...

Flanged Nut for the front suspension arm mountings. The integral flange spreads the clamp load across the joint face and helps the nut resist loos...

Flanged Nut for use in Land Rover assembly applications. The integrated flange acts as a built-in load-spreading face, distributing clamping force ...

Rear Air Spring for the electronic air suspension. Supports the rear of the vehicle and maintains ride height, inflating and deflating under contr...