Products

Water Pump Casing for the engine cooling circuit, the housing that carries the coolant pump and directs flow into the cylinder block. The casing l...

Steering Lever - LH - RHD is the left-hand steering arm that bolts to the front swivel pin housing. It provides the attachment point for the steer...

Accelerator Control Rod is a linkage rod that connects the accelerator pedal mechanism to the throttle shaft in the engine bay of Series II, Series...

Accelerator Rod in the throttle linkage. This rigid rod transmits accelerator pedal movement through the linkage to operate the engine throttle.

rod control GENUINE LR - 2.25 petrol and 2.6 petrol, 1968 onwards

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Flasher Lamp Lens - Sparto Type is the replaceable coloured lens for the Sparto-pattern direction indicator (flasher) lamp, forming part of the ext...

Valve Push Rod

Differential Shim - 0.072in, for the Rover-type differential. Fitted during differential setup to set bearing preload and gear alignment. Shim thi...

Water Pump Gasket - 7-Hole for the cooling system on Land Rover 4-cylinder military engines. This gasket seals the mating face between the water p...

Oil Filler Pipe Gasket seals the joint between the oil filler pipe and the engine front (timing) cover. Fitted at the filler pipe mounting flange,...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Temperature Sensor Adaptor - UNF-threaded adaptor for the water temperature transmitter. Screws into the engine coolant passage to accept the temp...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Differential Shim - 0.048in. Fitted during differential assembly to set bearing preload and gear alignment. Shim thickness is selected against mea...

Differential Shim for the crownwheel and pinion assembly. Fitted during differential assembly to set bearing preload and gear alignment. Shim thic...

Differential Pinion Shim - 0.052in. Fitted between the pinion head and its bearing to set pinion depth and preload during differential setup. Shim...

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Wiper and Heated Front Screen Switch - a dash-mounted control switch combining windscreen wiper and heated front screen functions. It operates the...

Battery Cable for the 24V electrical system. This is a battery link cable, connecting the two batteries so they supply the vehicle's 24-volt circu...

Manifold Stud - a mounting stud that secures the exhaust manifold to the cylinder head. It threads into the cylinder-head casting and projects thr...

Radiator Overflow Hose carries coolant overflow away from the radiator filler neck. It connects to the overflow spigot on the radiator filler neck...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Flywheel assy

Heater Control Pin

Front Bumper for the Series II, IIA and III Military Lightweight and Airportable variants, including JC3 specification vehicles. This bumper forms ...

Military fuel cap

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Clutch Cap that closes an aperture in the clutch bellhousing around the release mechanism. Fitted over an opening in the bellhousing, the cap seal...

M6 Stud for the gearbox main casing. This threaded stud secures the speedometer drive housing to the transmission main casing, providing the fixin...

Synchro Assembly for third and fourth gears in the LT95 four-speed gearbox. This synchroniser unit matches the shaft and gear speeds as 3rd or 4th...

Washer

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Brake Light Switch for the pedal box. It closes the stop-lamp circuit when the brake pedal is applied, switching on the brake lights. Used on brak...

Brake & Clutch Pedal Bush for the pedal box assembly. It forms the pivot bearing where the pedals mount on their shaft, locating the brake and ...

Shim bearing differential 0.062""