Products

Shim 1.65mm for Layshaft Speed - V8 4

Locking Washer for the swivel pin housing, fitted at the lower swivel pin. Its tab is folded against the retaining bolt to lock the fixing and prev...

Torsion Spring Sleeve for the lower tailgate. It fits over the tailgate torsion spring, forming a protective bearing sleeve at the pivot and preven...

Torsion Spring Sleeve for the lower tailgate. It fits over the tailgate torsion spring, forming a protective bearing sleeve at the pivot and preven...

Reverse Selector Fork for the Land Rover Series IIA and Series III 4-speed main gearbox, Suffix A build. This fork engages and disengages reverse ...

Thrust Washer

Layshaft Bearing Distance Piece Spacer for the layshaft (cluster gear) bearing within the main gearbox. It locates against the layshaft bearing to...

Washer 577254

Spring Ring

Fuel Gauge for the dashboard instrument cluster. An analogue gauge that indicates the quantity of fuel in the tank. It responds to the variable-re...

Switch Assembly

Stud for the carburettor-to-inlet-manifold joint. Threaded stud that secures the carburettor onto the inlet manifold flange. It provides the fixin...

Side Lamp Lens

pipe clip 1/2" (12.7mm) for 3/8" (9.5mm) hole

Wiper & Washer Switch

Inner Ring

Master Cylinder to Pedal Box Gasket for the hydraulic clutch circuit. This gasket seals the mounting face between the clutch master cylinder body ...

Exhaust Pipe - RH is the right-hand exhaust downpipe within the exhaust system. It bolts to the exhaust manifold outlet and carries combustion gas...

Exhaust Pipe

Accelerator Pedal Lever Pad is the moulded rubber pad that fits over the accelerator pedal lever. It provides the contact face between the driver's...

Oil Shield (front hub mudshield) for the front axle hub assembly. Fitted to the front hub on the Range Rover Classic, this shield sits between the...

Primary Pinion Bearing Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox casing. 2.05 mm thick, it control...

Heater Tap Adaptor for the heater control circuit. This zinc-plated mild steel adaptor forms the threaded interface between the heater water valve ...

Fuel Filler Hose

Shackle Pin for the rear shackle of the front leaf spring. The pin pivots the spring shackle at the rear eye of the front road spring, locating th...

Thermostat - the coolant-flow control valve in the engine cooling system, with an 82°C opening temperature. Mounted in the thermostat housing at t...

Breather Hose - Oil Filler to Flame Trap for the engine crankcase ventilation system. This flexible hose connects the oil filler pipe outlet to th...

Blanking Plate for the inlet manifold of the 3.5L V8 twin-carburettor petrol engine. The plate closes off an unused port on the manifold to maintai...

Throttle Cable Bracket within the carburettor throttle control. Anchors the outer throttle cable, providing a fixed abutment so the inner cable ca...

Ball Joint

Side Lamp Lens in white glass for the Lucas military-pattern side lamp. The lens presses into the side lamp body to seal the bulb aperture and diff...

Red Glass Lens - a replacement lens for an exterior lamp unit. The lens seats over the lamp body to seal the bulb chamber and colour the emitted l...

Amber Military Glass Indicator Lens - Used

Carburettor Jet is a calibrated metering jet fitted within the carburettor fuel circuit. It controls the rate of fuel flow into the airstream, set...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...