Products

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Intake Elbow Seal for the 3.5L V8 twin-carburettor petrol engine. The seal sits between the air cleaner intake elbow and the carburettor intake to ...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Carburettor Repair Kit for the six-cylinder petrol engine carburettor. It supplies the renewable service parts used to overhaul the carburettor and...

Splined End

Differential Thrust Washer Thrust washer for the differential gears within the Salisbury rear axle. It seats behind a differential gear in the fou...

Temperature Sensor mounted in the air filter (air cleaner) housing. This thermal sensor unit sits within the air intake housing and responds to th...

GENUINE LR camshaft sprocket for Rover V8 engines

Carburettor Gasket sealing the inlet manifold adaptor elbow to the carburettor on the Rover V8 twin-carburettor petrol engine. Fitted between the ...

Thermostat Housing Gasket seals the thermostat housing (water outlet elbow) to the intake manifold on the 3.5L carburettor V8 engine. It sits in t...

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Rear Brake Pad Kit - a complete set of disc brake pads for the rear axle, fitted to the rear brake calipers. The pads clamp against the rear brake...

Bottle Cap for the coolant expansion bottle. Seals the coolant expansion reservoir and maintains system pressure within the cooling circuit.

Accelerator Cable connecting the accelerator pedal to the throttle linkage on the 3.5L V8 petrol engine. The cable transfers pedal travel to the c...

Radiator Hose - the top hose of the engine cooling circuit, connecting the cylinder head outlet to the top of the radiator. It carries heated cool...

Door Latch Linkage Clip for the door latch and lock assembly. It retains the operating rod on the latch mechanism. The clip holds the handle-to-la...

Cup Washer is a dished washer used at the gearbox tie-rod (stabiliser rod) to chassis mounting on Series models. The cupped profile seats against ...

Retaining Clip used to hold the lock barrel in place. Supplied as a single clip.

Set Screw retaining the top cover plate of the Series gearbox. A 4BA round-head fastener, sherardised finish, used to secure the cover plate on to...

Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...

Screw for securing the window catch on Series hard top body variants. Used in the hard top glazing and catch assembly to retain the window catch m...

Upper Tailgate Screw, a fixing used in the upper tailgate assembly. It secures the upper tailgate components in place, providing a threaded fasten...

Spire Nut, a J-type sheet-metal spring nut (also known as a speed nut) used to secure trim, panels and fittings. The nut clips over a panel edge o...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Brake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...

Heater Control Bulb illuminates the heater and ventilation control panel. Fitted into the front HVAC control assembly, it backlights the heater co...

Clutch Driven Plate - the friction disc within the clutch assembly, mounted on the splined gearbox input shaft between the flywheel and the clutch ...

Clutch Plate & Cover Assembly forms the driven and clamping elements of the clutch, sitting between the engine flywheel and the gearbox input s...

Fuel Spill Return Pipe - part of the fuel injection system, connecting the injector leak-off ports to the fuel return line. It collects spill (lea...

Bush

Exhaust Valve Guide for the 2.6L six-cylinder petrol engine. The guide is pressed into the cylinder head and locates the exhaust valve stem, holdin...

Shakeproof Washer – a serrated, externally toothed lock washer used at the clutch hydraulic hose union. The teeth bite into both the mating surfac...

Snap Ring

Gearbox Filter Plug for the LT77 five-speed manual gearbox. The plug closes the bore in the extension case that gives access to the gearbox oil fil...

Exhaust Mounting U-Bolt used to clamp and secure the exhaust system to its mounting bracket on the Range Rover Classic. This U-bolt wraps around t...