Products

Bolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...

Dowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...

Fuel Pump Gasket seals the external fuel pump to its mounting face in the fuel delivery system, preventing leakage at the joint. Used on petrol ap...

Heater Control Cable - Heat Outlet for Defender 90 and 110 vehicles. This Bowden cable connects the heat outlet control lever on the heater contro...

Pinion Oil Seal - seals the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Self-Tapping Screw for body and trim fixing applications. Used to secure window surrounds, bodyside trim, facia and switch panels. The self-tappin...

Headlamp Screw is a fastener used in the front headlamp assembly. It secures the headlamp unit and rim within their mounting, holding the lamp in ...

Screw – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...

Screw - a threaded fastener used across several exterior body fixings. It secures fittings within the radiator grille, the rear end door seals and...

Self-Tapping Screw is a fixing that secures the steering column shroud in place. Being self-tapping, it forms its own thread as it is driven, retai...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Screw - a No. 10 x 1" pan-head self-tapping screw used across interior and door assemblies. It secures the window regulator and door glass channel...

Screw - No.10 x 1" Pan head, self-tapping, pointed fastener used in door trim and window regulator assemblies. It secures the interior grab handle...

Self-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...

Self-Tapping Screw securing the heater assembly within the HVAC housing on diesel applications. This screw forms part of the heater box fixing har...

Brake pipe clip

Cable Tie for securing wiring looms and cables in Land Rover applications.

Fan Motor for the in-dash air conditioning condenser and receiver-drier assembly. The motor drives the fan that draws air across the condenser and...

Resistor Assembly sets the blower motor fan speeds within the heating and air conditioning system. Wired in series with the blower motor on the lo...

Throttle Disc is the throttle butterfly for the Solex carburettor, operating in the air and fuel induction system. Mounted on the throttle spindle...

Screw for the valve rocker (rocker shaft) assembly of the VM 2.4L and 2.5L 4-cylinder turbo diesel engine. Retains the rocker gear on the cylinder...

Rocker Cover O-Ring for the VM four-cylinder turbo diesel engine, sealing the rocker (cam) cover to the cylinder head. It maintains the oil-tight ...

Injector Bush for the VM 2.4L and 2.5L 4-cylinder turbo diesel engine in the Range Rover Classic. This bush is fitted at the cylinder head to loca...

Carburettor Overhaul Kit for the 2.25L four-cylinder petrol engine. The kit renews the perishable sealing and metering components of the carburetto...

Carburettor Float Needle is the needle valve that regulates fuel entry into the carburettor float chamber. Actuated by the float, it seats to shut...

Seal kit NLA NLA NLA

Oil Seal

Tab Washer for the steering box drop arm retaining nut. This lock washer sits under the nut on the steering box output shaft. Once the nut is torq...

Starter Motor Brush Kit for the Lucas M113-type starter motor in the engine starting system. The brushes bear on the armature commutator to transf...

Reinforcement is a structural stiffener for the lower rear body. It fits to the lower section of the rear body structure to add rigidity to the sur...

Pipe Clip used to secure and route pipework such as fuel breather and roll-over anti-spill lines. The clip holds the pipe at a fixed point to prev...

Body Washer, 22mm outer diameter, 6.5mm inner diameter. A flat washer that spreads the clamping load of a fixing across the mounting surface, prot...

Washer for the bonnet insulation pad. This washer retains the sound- and heat-insulation pad against the underside of the bonnet, holding the pad ...