Products

Sunroof Seal for the glass sunroof panel, part of the sunroof assembly. The seal runs around the perimeter of the sunroof glass and bears against ...

Wiring Connector for the chassis wiring harness, used in the fuel tank circuitry. The connector forms a serviceable electrical junction between ha...

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Instrument Bulb Holder for the early Discovery 1, providing the retaining socket for an illumination bulb within the instrument cluster assembly. ...

Rotor Arm for the 24V shielded ignition distributor. The rotor arm mounts on the top of the distributor shaft and, as it rotates, routes the high-t...

Thermostat regulates coolant flow within the engine cooling circuit of the 2.5L 4-cylinder VM Turbo Diesel. Housed in the thermostat housing at th...

Door Handle Assembly is the exterior handle for the left-hand front door, part of the front door locks and handles assembly. It mounts to the oute...

Door Lock Barrel is the key-operated lock cylinder for the door, part of the door locks and handles assembly. It fits the exterior door lock and t...

Quarter Window Catch is the latching assembly for the side-opening rear quarter window, in the Lunar colour finish. Mounted to the hinged quarter ...

Kit - Mudflap - Rear

Rear Quarter Panel is the right-hand rear body side panel, forming the outer body section between the rear door aperture and the rear of the vehicl...

A/C System Clamp is a securing clamp used within the air conditioning and heater (HVAC) system. It retains components of the A/C intake and distri...

A/C Evaporator Seal seals the evaporator assembly within the air conditioning system's HVAC housing. Fitted at the evaporator core interface to pr...

Rear Floor Mat Set is a drop-in moulded rubber mat set for the rear floor area. The mats locate over the rear footwell and floor pan to protect th...

Brush kit RTC830 fits: Rover 3.5L V8 startermotor type 3M100 - S3 109" stage 1 V8 - 101" Forward Control - Range Rover Classic

Rivet - body fixing used in the rear cab panel and sliding side window assembly. Secures the panel and window frame to the surrounding body struct...

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Body Rivet - general-purpose body fixing used across the cab structure, front wings, hood sticks, rear body cappings and panels, and door seal rete...

Front Knuckle - right-hand steering knuckle (hub carrier) within the front suspension and hub assembly. Carries the front wheel bearing and hub, a...

Retainer

Air Suspension Transfer Relief Valve - solenoid valve in the air suspension compressor and supply circuit, mounted at the supply reservoir. Contro...

Transfer Relief Valve - Front Axle in the electronic air suspension system. Fitted in the front axle branch of the air suspension pneumatic circui...

Anti-Roll Bar Bush - a mounting bush in the rear suspension anti-roll (stabiliser) bar assembly. It clamps the rear anti-roll bar to the body, loc...

Anti-Roll Bar Bush for the front suspension, locating the front anti-roll (stabiliser) bar to the body. The bush clamps around the bar and allows ...

Plug for the hydraulic valve block of the Active Anti-Roll Bar system with Roll Stability Control. The valve block contains the solenoid and relie...

Clip retaining the top of the rear air spring within the rear spring and shock absorber assembly. The clip locates and secures the air spring at i...

Eccentric Washer - an adjusting washer used at the front suspension arm pivot mounting. The offset (eccentric) hole allows the arm's pivot bolt po...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Bolt Mounting bolt for the rear suspension arm. Part of the rear multi-link suspension assembly, it secures a rear upper or lower suspension arm a...

Bolt Mounting bolt for the front suspension arm. Part of the front suspension assembly, it secures a front upper or lower control arm (wishbone) a...

Hex Head Bolt - M6 x 20mm flanged bolt used as a general-purpose fixing at numerous points on the vehicle. The integral flange spreads the clampin...

Bolt - Hexagon Head used in engine and interior fascia assembly applications. This hexagon head fastener is used in the EGR system assembly and in...