Products

Holder - Cup

Holder - Cup

Light Guard - Rear Upper Protective guard for the upper rear lamp cluster, forming part of the exterior lighting protection assembly. The guard mo...

Cylinder Head Kit

Radius Arm Bush is the compliant mounting bush at the radius arm pivot in the front suspension. The radius arm locates the front axle fore-and-aft...

Folding Side Step mounts beneath the side door sill to provide a sprung step that aids entry and exit, folding up against the body when not in use ...

Sunroof Seal for the manual sliding sunroof. The rubber seal fits around the sunroof aperture and seals the panel against the roof to keep out wate...

Interior Floor Mat Set in beige, laying over the cabin floor to protect the original carpet from wear, dirt and moisture. The mats are shaped to t...

Front Fog Lamp Bezel for the left-hand side, the trim surround that frames the front fog lamp within the bumper aperture. It locates around the fo...

Cover - Spare Wheel

Hard Spare Wheel Cover - 15" is a rigid cover that fits over the externally mounted spare wheel. The hard-shell construction shields the spare whe...

Spare Wheel Cover - a moulded vinyl cover that fits over an externally-mounted 16" spare wheel to shield the tyre and rim from dirt, moisture and U...

Waterproof seat cover for a single outer front seat, finished in grey. The cover is shaped to the standard seat frame and fits over the existing u...

Rubber floor mat set for the passenger compartment, supplied as a complete vehicle set. The mats are shaped to the footwells and drop in over the ...

Lamp

Spare Wheel Cover - a padded vinyl cover that fits over an externally mounted spare wheel to protect the wheel and tyre from weather and dirt. Size...

Hazard Switch Bulb Illumination bulb for the hazard warning switch within the facia switch assembly. It provides the internal lighting that illumi...

These locking wheel nuts are suitable for all alloy wheels that use original Land Rover alloy wheel nuts. Set of 5 locking wheel nuts and 1 key.

Locking Wheel Nut Kit for alloy road wheels, part of the road wheel and fixings assembly. Each locking nut replaces a standard wheel nut at one pos...

Locking Wheel Nut Cap in stainless steel, fitting over the exposed end of a locking (anti-theft) road wheel nut. The cap conceals and protects the...

Wire - Ignition

Heater To Bulkhead Seal seals the joint between the heater and blower duct and the bulkhead aperture, within the heating and ventilation assembly. ...

Wastegate Actuator Pneumatic actuator that regulates turbocharger boost pressure on the 2.5L 200TDi turbo diesel engine. Mounted on the turbocharg...

Thread Strip Front - RH

Sunroof Handle Assembly operates the manually-operated glass sunroof, forming the interface between the occupant and the roof panel's opening mecha...

Wiper Drum Adaptor - splined adaptor used in the windscreen wiper system to connect the wiper arm to the splined wiper spindle. The adaptor seats ...

Clutch Damper for the Defender Puma hydraulic clutch circuit. This in-line hydraulic damper installs within the clutch hydraulic hose run between ...

upper Tube clutch pipe GENUINE LR - LHD Defender TD5/PUMA

Bolt, high tensile, M8 x 25mm. A metric hexagon head bolt for body, chassis, and structural fastening applications.

Accelerator Cable for the throttle control linkage, connecting the accelerator pedal to the engine's throttle mechanism. The cable transmits pedal...

Handbrake Actuating Pawl Rod Actuating rod within the rear parking brake mechanism of the drum-in-disc handbrake assembly. It transmits handbrake ...

Parking Brake Adjuster Kit for the rear parking brake (drum-in-disc) mechanism. The kit renews the adjuster components that set the clearance betw...

Rocker Cover Screw for the Rover V8 petrol engine. This 1/4" UNC screw secures the valve (rocker) cover to the cylinder head. The rocker cover per...

Brake Disc Bolt - M10 x 20mm securing the brake disc to the hub flange. M10 x 20mm bolt with 1.5mm thread pitch. Multiple bolts are required per d...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Front Axle Differential Casing for the front drive axle. This casting forms the central housing of the front axle. It carries the differential cro...