Products

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...

Blanking Plug closes off an unused 8mm (5/16 inch) aperture in a body panel or chassis section. It belongs to the body grommets and panel-sealing g...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Striker Plate

Bush GENUINE LR sold EACH! for fitting air intake grille 90/110/130 and for fitting old type individual letters "Range Rover"

Grommet fits the bonnet release and locking mechanism. It lines the panel aperture through which the bonnet release cable passes, sealing the open...

Sedimentor Drain Plug with Seal for the diesel fuel filter assembly. Fitted at the base of the sedimentor bowl, this plug allows the bowl to be dr...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Door Control Unit - 2-Door

Door Lock Striker is part of the door locking assembly, mounted on the body aperture at the door pillar. The door latch engages the striker as the...

Front Air Grille covers the fresh air intake at the base of the windscreen, forming part of the fresh air system that feeds the heater and ventilat...

Door Hinge Bolt A fixing screw for the front door hinge, part of the door hinge mounting hardware. It secures the hinge to the body pillar and doo...

Mounting Angle is the left-hand front bracket within the front wing and deck panel assembly. The angle bracket locates and supports the front wing...

Mounting Angle is a front bracket within the front wing and deck panel assembly. The angle bracket locates and supports the front wing and deck pa...

Door Lock Assembly - RH for the Range Rover Classic 2-Door Station Wagon. Fitted to the right-hand door, this lock unit provides the latching and ...

Roll Pin for Door Hinge on the Range Rover Classic. A small cylindrical spring pin that locates and retains components within the door hinge assem...

Tailgate Seal - the weather seal for the upper tailgate, part of the rear body closure assembly. Fitted around the upper tailgate aperture, it for...

Tailgate Seal - the weather seal for the upper tailgate, part of the rear body closure assembly. Fitted around the upper tailgate aperture, it for...

Upper Tailgate Lock Barrel & Key secures the upper tailgate (load door) and provides key-operated locking. Supplied as the lock barrel with it...

Front Door Hinge Set Screw secures the front door hinge to the body pillar and door within the door mounting hardware. It clamps the hinge leaf in...

Edge Clip A black edge clip with a delta-section profile that grips a panel flange. It provides a push-on fixing along the edge of the door assemb...

Warning Label A warning label relating to the battery negative (earth) cable connection. It is applied in the vehicle to convey a safety instructi...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Plain Washer A flat plain washer that spreads the clamping load of a fastener over the mounting surface. Used in body panel and interior fixings.

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

In/out member spring

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Locking plate

Circlip for the throttle linkage on the carburettor V8 engine. It retains a pin or clevis within the throttle linkage, holding the linkage componen...

Washer - a plain flat washer with a 10.5mm internal diameter, sized for M10 fasteners. It seats under a bolt head or nut to spread the clamping lo...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

O-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...

O-Ring for the engine sump, part of the engine lubrication sealing arrangement. Seals the sump joint to prevent oil leakage. Fitted to four-cylind...

Speedo cable oil seal retainer plate

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Differential Shim, 0.040in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Differential Shim - 0.060in. Fitted during differential assembly to set bearing preload and gear alignment. Shim thickness is selected against mea...

bush shock absorber OEM, bush anti roll bar OEM

Exhaust Flange forms a bolted joint in the exhaust system of the early 3.5L V8 petrol engine with single downpipes. It provides the sealing face w...