Products

Transmission Handbrake Shoe Set is the friction pair for the drum-type parking brake mounted on the rear output of the transfer box. When the hand...

Hex Bolt, grade 8.8, M8 x 20mm. A standard metric hexagon head bolt. Grade 8.8 indicates a tensile strength of 800 MPa and a yield strength of 640...

Stub Axle Bolt is a hex-head retaining screw that secures the front stub axle to the swivel pin housing. The stub axle carries the wheel hub and b...

Brake Union Washer is a sealing washer for hydraulic brake line connections. It seals the joint at a brake pipe or flexible hose union, fitting be...

Bolt and Washer - an M8 x 25 mm hexagonal-head bolt supplied with a washer. A general-purpose threaded fastener used at various fixing points on t...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Timing Belt Tensioner Stud mounts the timing belt tensioner to the engine front cover. Used on the 2.5L 200 TDi diesel engine, it provides the thr...

Front Axle Drive Shaft transmits drive from the front differential to the right-hand wheel hub, forming part of the front axle drive shaft and hub ...

Front Drive Shaft, left-hand, part of the front axle drive assembly. The shaft transmits torque from the front differential to the front wheel hub...

Front Half Shaft for the right-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant vel...

Front Half Shaft for the left-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant velo...

Coil Spring - Front - +2" Light Duty is a front suspension coil spring providing approximately 50mm (2 inches) of lift above the standard ride heig...

Coil Springs are a matched front pair that raise ride height by 2 inches (50 mm) above standard, forming part of the coil-sprung front suspension. ...

Terrafirma medium load rear springs (pair) 90/D1/RRC

Rear Coil Spring - Heavy Duty, +2" Lift A rear suspension coil spring from the Terrafirma range, seating between the axle and the chassis spring s...

Suspension Bush - Rear Lower, polyurethane, supplied as a set of two bushes with internal sleeves and installation grease for the axle-end mounting...

Bush Kit - Front Radius Axle Arm End

Radius Arm Bush Kit - Chassis End, Front (Terrafirma). A set of four uprated polyurethane bushes for the front radius arm mountings, replacing the...

Rear Radius Arm Bush Kit - Chassis End, supplied as a set of four polyurethane bushes with retaining plates, inner sleeves, and installation grease...

Front Axle Panhard Rod Bush - Late Type, for replacement at the Panhard rod mounting point on the front axle assembly. The bush provides the compl...

Extended Bump Stops are compression-travel limiters that sit between the axle and the chassis to cap suspension up-travel and cushion the axle agai...

Bump stops, standard height - front or rear axle. The bump stop absorbs the last part of suspension compression, cushioning axle-to-chassis contac...

Anti-Roll Bar Link & Shock Bush Kit renews the compliant mounting bushes in the anti-roll bar link and shock absorber mounting points within th...

Panhard Rod Bush Kit - replacement polyurethane bush set for heavy-duty adjustable Panhard rods, within the axle lateral-location assembly. The Pa...

A-Frame Ball Joint Bracket forms the pivot connection at the apex of the rear axle A-frame linkage. It mounts to the rear axle housing and locates ...

Weld-On Beadlock Ring Kit - a set of four steel beadlock rings for converting 16in steel wheels to a mechanically clamped tyre bead. The inner rin...

Extended Wheel Arch Set - a set of four oversize wheel arch extensions for three-door bodywork, standing 2in (50 mm) wider than the standard arches...

Locking Wheel Nut Set secures the road wheels to the hub with a keyed nut pattern that cannot be removed with a standard socket, deterring wheel th...

Extended Wheel Arch Set - a set of four oversize wheel arch extensions for five-door bodywork, standing 2in (50 mm) wider than the standard arches....

Front suspension shock absorber designed to control spring oscillation and maintain tyre contact with the road surface. Twin-tube low-pressure ni...

Rear Shock Absorber, standard-travel, for the rear axle suspension. The damper controls vertical movement of the rear axle and damps spring oscill...

Shock Absorber - Front - +2" Travel for the front coil spring suspension system, designed for use with a 2-inch suspension lift. The extended-trav...

Rear Shock Absorber provides damping control on the rear axle for suspension set up with approximately 50 mm of additional travel. Twin-tube const...

Front Shock Absorber provides damping control on the front axle for suspension raised by approximately 50 mm. Twin-tube big-bore construction with...

Rear Shock Absorber provides damping control within the rear axle spring and damper assembly for suspension set up with extended travel. Twin-tube...

Absorber Shock

Big Bore Expedition Shock Absorber - front position, standard ride height. The damper installs between the front axle mounting and the chassis bra...

Shock Absorber for the rear coil spring suspension system. This big-bore unit is designed for heavily laden and expedition applications where sust...

Front Shock Absorber for the front axle suspension assembly, controlling vertical wheel movement and stabilising the coil spring through compressio...

Rear suspension shock absorber designed to control vertical movement of the axle and dampen spring oscillation within the suspension system. This...

Mega Sport Monotube Shock Absorber with 11 inches of travel and a remote gas reservoir, usable in either the front or the rear position. The monot...

Seal Kit - 11" Travel Shock

Replacement Damper Shaft for the 11 inch travel Mega Sport monotube shock absorber. The shaft carries the damping piston and passes through the se...

Nylon Pad for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The pad forms the contact face at the end of the bump stop...

Seal Kit - Bump Stop

Internal Spacer for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The spacer fits inside the bump stop to shorten the ...

Valve for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The TF140 is a monotube, nitrogen-charged unit adjustable betw...