Products

Bulb 24V 21/5W dual-filament bulb for 24-volt electrical systems. The 21W filament serves the stop light circuit and the 5W filament serves the tai...

Sediment Retainer for the fuel lift pump glass sediment bowl - the clamp that secures the glass bowl to the underside of the pump. It holds the bo...

Braided Earth Strap with Battery Clamp - 300mm for the vehicle electrical grounding circuit. This braided copper earth strap is fitted with an int...

Nut is a hexagonal nut cut with a 7/16" BSF (British Standard Fine) thread. It threads onto a matching 7/16" BSF bolt or stud to secure a bolted j...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Axle casing oil seal

Circlip - Rear Mainshaft Bearing for the Series Land Rover gearbox. This circlip retains the rear mainshaft bearing within the gearbox casing, pre...

Handbrake Stud A mounting stud for the transmission (drum) handbrake within the braking system. It secures the transmission brake back plate to th...

Transfer Case Intermediate Gear with a 44/22 tooth configuration, operating within the transfer box gear train. The intermediate gear meshes with ...

Flexible Brake Hose - hydraulic hose carrying brake fluid from the rigid chassis or axle pipe to the wheel cylinder. Forms the flexible link acros...

Four-Wheel Drive Selector Lever Bush for the transfer box gearchange linkage. The bush locates the four-wheel-drive selector lever at its pivot, t...

Swivel Pin Seat Cone for the front axle swivel housing. This cone provides the precision seating surface on which the swivel pin locates within th...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Selector Shaft for the Series I, II, IIA, and III transfer case. This shaft is part of the transfer case gear-selection mechanism, transmitting th...

Joint Washer for the gearbox output shaft housing. This gasket seals the mating face between the output shaft housing and the gearbox casing, prev...

Collar Bush for the four-wheel-drive selector mechanism in the two-speed transfer box. It seats on the high-range 4WD selector rod, locating the s...

Plunger for the transfer box selector mechanism. Locates within the transfer selector assembly to provide positive engagement and detenting of tra...

Transfer Box Output Mud Shield Shield that fits over the transfer box output flange to protect the output shaft oil seal from mud, water and debris...

Gearbox Mainshaft Oil Seal for the rear of the manual gearbox, sealing the mainshaft where it passes through the rear of the mainshaft-and-gears se...

Mudshield Output Shaft

Swivel Pin

spring road front SWB 9 leaf Passenger Side

Wheel Cylinder for the drum brake assembly - the right-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either...

Wheel Cylinder for the drum brake assembly - the left-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either ...

Wheel Cylinder for the rear drum brake assembly, right-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hy...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Wheel brake cylinder LH

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Main Starter Spring is the principal return spring within the starter motor assembly used on Series I, II, IIA, and III vehicles. It operates withi...

Camshaft Cover Gasket seals the camshaft cover plate to the cylinder block, forming part of the camshaft housing and engine lubrication boundary. ...

Set Screw - Water Pump Spindle is a locking fastener that locates the water pump spindle within the water pump housing on Series engines produced b...

Banjo Bolt for the timing chain tensioner hydraulic oil feed on Land Rover 2¼ Litre and 2.0 Litre diesel engines. The banjo bolt is a hollow faste...

Rocker Cover Stud for the cylinder head on early Land Rover 4-cylinder engines. The rocker cover stud is a threaded fastener installed into the cy...

Wing Nut with a 1/4" BSF thread, tightened by hand without tools. Used to secure the battery clamp frame and the oil-bath air cleaner clamp, where...

Bolt - 1/2 UNF x 1 is a hexagon-head set bolt in 1/2 UNF (Unified National Fine) thread, 1 inch in length, used to secure the engine mounting brack...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Sealing Ring A rubber O-ring sealing ring serving two separate shaft and tube interfaces. It is used on the transfer box high/low range selector s...

Mainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...