Products

Lashing Eye - 102 x 95mm - Flush-Mount is a heavy-duty tie-down anchor point designed for flush installation into a load bed or cargo floor. The e...

Exhaust Connecting Pipe is the intermediate section of the exhaust system, linking the front downpipe to the rear silencer assembly in the Series E...

Flasher Unit for the direction indicator (turn signal) circuit. This is a 12V three-pin thermal, can-type flasher that switches the indicator lamps...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Gasket

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Diesel Fuel Decal is the self-adhesive caution label applied at the fuel filler to identify the tank as diesel. It marks the filler point so the v...

Carburettor Spring - Solex - a spring used in the Solex carburettor of the 2.25 litre petrol engine, part of the fuel system. It supplies the spri...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

In/out member spring

Brake & Clutch Reservoir Tank Kit

Shackle Shim Ring - 0.003in shim used to set the gap on extended spring shackles. Fitted against spacer tube 504211 to take up clearance on the sh...

Lock Nut, 5/16 BSF, a self-locking nut used on the transmission parking-brake assembly. It retains the transmission (handbrake) brake drum, its se...

Plain Nut for use as a standard fastener across Land Rover applications. A plain (non-locking) hex nut for general assembly and repair work.

Tappet Adjuster is the adjustment screw used to set valve clearance in the cylinder head of Land Rover Series 4-cylinder engines. The screw thread...

Thrust Washer for the gearbox mainshaft, 0.128" thick. This is a selective-thickness thrust washer used to set mainshaft end-float during gearbox ...

Thrust Washer - Mainshaft - 0.130 Inch is a gearbox internal component positioned at the 3rd gear location on the mainshaft in the Series 1, Series...

Gear Lever Locating Pin locates and retains the main gear lever within the manual gearbox. It holds the lever against its pivot so that shift move...

Switch - Fuel Tank Tap is an electrical switch used to operate the fuel tap selection on Land Rover Series I, Series II, Series IIA, and Series III...

Inlet Valve Guide - a cylinder-head valve guide for the inlet valves of the 2.6L six-cylinder petrol (IOE) engine. Pressed into the cylinder head,...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Locking plate

Road Spring SWB Rear 11L

Rear left-hand leaf spring designed for short wheelbase Land Rover Series vehicles. This road spring is configured with 11 leaves and is intended ...

Front Exhaust Pipe for petrol applications. This is the front section of the exhaust system, carrying gases from the exhaust manifold rearward to t...

Wiper Gear Linkage for the windscreen wiper system, transmitting drive from the wiper motor to the wheelbox and wiper spindle. It converts the rot...

Union Nut for the diesel fuel filter housing, part of the fuel supply circuit. The union nut secures a fuel feed pipe union to the filter housing,...

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

Rubber Mat

Circlip for the throttle linkage on the carburettor V8 engine. It retains a pin or clevis within the throttle linkage, holding the linkage componen...