Products

Camshaft Sprocket for the timing drive of the Ingenium engine family - the 2.0L and 3.0L diesel and 3.0L petrol units. Mounted on the end of the ca...

Valve Rocker Arm for the cylinder head valvetrain. It transfers camshaft lift to the valve, actuating the valve as the camshaft rotates. Fitted to...

Valve Stem Seal seals the valve stem where it passes through the valve guide in the cylinder head of Ingenium diesel engines. Fitted over the top ...

Valve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...

Camshaft Position Sensor monitors camshaft rotation for the engine management system. Mounted in the cylinder head and camshaft cover, it signals ...

Adhesive and Sealer is a glass bonding adhesive and sealer used to seat and seal fixed automotive glazing to the body. It bonds and seals the wind...

CV Boot Kit

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Bolt for the drive belt and pulley assembly on the AJ200 / AJ20 engine family. This fixing secures a pulley or tensioner component at the front of...

MAP Sensor is the manifold absolute pressure and charge-air temperature sensor mounted in the inlet manifold. It reports intake manifold pressure ...

Cylinder Head Bolt for Ingenium petrol engines (1.5L AJ20P3, 2.0L AJ200 / AJ20P4, 3.0L AJ20P6 / AJ22P6). The bolt clamps the cylinder head to the ...

Screw and Washer - M5 x 20 is a self-tapping fastener with a captive washer, an M5 thread, 20 mm length and a hex head. It secures body panels, sp...

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Mass Air Flow Sensor in the engine air intake system, fitted in the intake tract between the air filter and the throttle and turbocharger inlet. It...

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

Wheel Cover set, fitted over the road wheels. The covers clip over the wheels to give a finished appearance and shield the wheel face from road di...

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Wheel Cover for the road wheel. The cover fits over the wheel to give a finished appearance and shield the wheel face from road dirt and brake dus...

Nut used in exterior body panel and trim fixings. Secures body components such as the luggage compartment door finisher, radiator grille and bumpe...

Diesel Exhaust Fluid (AdBlue) for diesel vehicles fitted with a selective catalytic reduction (SCR) exhaust after-treatment system. The fluid is h...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Clip for exterior body trim and accessory fittings. The clip retains body mouldings, side steps, mudflaps and related exterior trim to the body, p...

Valve stem seal for the cylinder head valve train. The seal locates on the valve guide and wipes the valve stem as it reciprocates, metering the s...

Cylinder Head Gasket sealing the cylinder head to the cylinder block. It contains combustion pressure at each bore and seals the coolant and oil g...

Coolant Bleed Hose - small-bore hose in the engine cooling system, running from the cylinder head bleed point to the coolant expansion tank. It ve...

Pump - Water Hepu

Coolant Bypass Tube - rigid coolant transfer tube in the engine cooling system, connecting the thermostat housing to the heater water circuit. It ...

Front Crankshaft Oil Seal - radial lip seal in the cylinder block and front cover assembly, sealing the crankshaft nose where it passes through the...

Camshaft Cover Gasket - moulded gasket sealing the camshaft cover to the cylinder head. It seals the valve train and cam carrier area against oil ...

Drive Belt - V-belt in the front-end accessory drive of the 3.0L Ingenium six-cylinder petrol engine, driving the belt-integrated starter generator...

Drive Belt - ISG - V-belt in the front-end accessory drive of the 3.0L Ingenium six-cylinder petrol engine, driving the belt-integrated starter gen...

Rear Crankshaft Oil Seal - the main oil seal at the flywheel end of the crankshaft, part of the crankshaft sealing arrangement on the Ingenium engi...

Fuel Injector for the 3.0L AJ20D6 Ingenium six-cylinder diesel engine in high-output specification, part of the high-pressure common rail fuel inje...

Bolt for the camshaft timing gear, part of the Ingenium engine timing drive. It retains the timing sprocket to the camshaft, transferring drive fr...

Bolt for the camshaft timing gear, part of the Ingenium engine timing drive. It retains the timing sprocket to the camshaft, transferring drive fr...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...