Products

A-frame Ball Joint Fitting Kit – the mounting hardware for the rear A-frame ball joint and its housing. The fixings secure the ball-joint housing t...

Headlamp body

Brake Calliper Piston and Seal Kit - Rear Axle - overhaul set for the rear brake callipers, part of the rear foundation braking assembly. Calliper...

Turret Fitting Kit - Galvanised - Front - Pair

Alternator upgrade kit for the 200Tdi 2.5L 4-cylinder turbo diesel, replacing the standard alternator in the engine charging circuit with a higher-...

200 TDi Type Engine Alternator - Discovery

Timing Belt Kit - Defender 200TDi

Air-operated differential locker for a 24-spline differential, replacing the standard differential centre in the axle. When engaged, it locks both...

Rear Bush Kit for the trailing arm and A-frame rear suspension assembly. This kit provides the rubber bushes for the chassis mounting points of th...

Rear suspension bush kit covering the trailing arm and A-frame mounting points of the rear coil-sprung suspension. The trailing arms locate the re...

Gear Change Kit - R380

Double Cardan Joint Kit for the Discovery 2 front propshaft. The Discovery 2 front propshaft uses a double cardan joint assembly incorporating thr...

Connector - 5-Way Switch - Black - a black five-way connector housing used in the vehicle wiring harness. The housing mates to a five-pin switch a...

Front Propshaft Flange Bolt Kit - the high-tensile fasteners that secure the front propshaft to its mating flanges at the transfer box and axle end...

Throttle Potentiometer Kit adapts the Rover V8 plenum chamber to accept a Colvern throttle position sensor in place of the original two-bolt potent...

Head Bolt Set for the 300 TDi 2.5L turbo diesel engine - the bolts that clamp the cylinder head to the engine block. These are torque-to-yield (st...

Cylinder Head Bolt Kit - a set of cylinder head bolts for the 2.5L 200 TDi turbo diesel engine. The bolts clamp the cylinder head to the block acr...

Towing Bracket Slider is the sliding tongue section of a Dixon Bate adjustable towing bracket, which sets and locks the hitch at the required heigh...

Tow Ball & Pin Hitch Assembly for the towing system, mounting to the rear towing bracket. The assembly combines a tow ball for standard ball-c...

Head Bolt Kit - a complete set of cylinder head bolts for the Rover V8 engine, securing the cylinder heads to the block and clamping the head gaske...

Rear Dislocation Cone is a suspension component for the rear coil springs, fitted at the spring seat to guide a spring that unseats at full droop b...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

Differential Guard for the axle differential, protecting the diff housing and cover from impact damage off-road. Clamps over the differential cent...

Differential Guard is a galvanised bolt-on steel guard that shields the differential housing on the axle from impact and debris off-road. It clamp...

Front Radius Arm Bush Kit - renews the rubber bushes at the rear ends of the front radius arms, where they mount to the chassis. The radius arms l...

Wheel Arch Trim Kit providing a full six-piece set of extended wheel arch flares that fit over the standard arches. The flares extend approximatel...

Oil pump pressure relief valve repair kit for the 300 TDi engine lubrication circuit. The pressure relief valve sits in the oil pump housing at th...

Stainless Braided Brake Hose Kit - a set of flexible brake hoses for the hydraulic braking circuit, supplied in +40mm extended lengths for vehicles...

Wheel Nuts - set of five, sufficient to secure one wheel. The nuts are sized for the MaxXtrac Mach 5 alloy wheel, giving the correct seat and thre...

Locking Wheel Nut Kit - a set of five locking wheel nuts in a black finish, fitted in place of standard wheel nuts to secure the road wheels to the...

Alloy Wheel from the Maxtrac Blindo range, finished in anthracite. Specifications: Size: 16 x 7 inches Bolt pattern (PCD): 5 x 165 Offset (E...

The Maxtrac Blindo 16x7 alloy wheel is designed for off-road durability and rugged performance, making it the perfect choice for Land Rover and 4x4...

Alloy Wheel is a single-piece 16 x 7-inch alloy road wheel finished in black. It has a five-stud 5x165 mm bolt pattern and an ET20 offset, which s...

Waterproof Seat Cover Set for the rear seats, tailored to the split rear bench. The set contains a cover for the two-seat section (back and base),...

Carburettor Conversion Kit - replaces the twin Stromberg or SU carburettor setup on the Rover V8 with a single four-barrel carburettor mounted on a...

Gearbox - LT77 five-speed manual transmission, supplied as a reconditioned complete unit. The LT77 bolts directly to the engine bell housing and d...

The Jackall 48" Large Base Jack is the ultimate heavy-duty lifting solution for a variety of applications. With a massive 8,000lbs capacity, this j...

Ensure accurate engine timing with this 12-piece timing tool kit, designed for Land Rover 2.5D, 200TDI, and 300TDI engines. This comprehensive kit ...

Swivel Kit - complete swivel housing overhaul kit for one side of the front axle. The swivel housing ball carries the stub axle and encloses the c...

Swivel Kit - complete swivel housing overhaul kit for one side of the front axle. The swivel housing ball carries the stub axle and encloses the c...

Swivel Repair Kit - swivel housing service kit for one side of the front axle, supplied without the swivel housing ball. It renews the sealing and...

Swivel Kit - overhaul kit for one front swivel housing assembly. The swivel housing is the steering pivot at the outer end of the front axle case: ...