Products

Exhaust Clamp Kit for the intermediate pipe section of the exhaust system. The kit provides the clamps that secure the intermediate exhaust pipe a...

Exhaust Clamp Kit - the clamping hardware that secures the intermediate pipe joint in the exhaust system, holding the intermediate section to its a...

Exhaust Clamp Kit for the front and intermediate exhaust sections on Series II and III Land Rovers equipped with the 2.6L six-cylinder petrol engine.

Exhaust Clamp Kit for the silencer and tail pipe section of the exhaust system on Series II and III 88-inch Land Rovers with a right-hand side exha...

Sidelight Bulb, rated 24V 10W, for the front sidelight (parking light) position. The bulb seats in the sidelight holder within the front lamp asse...

Bulb rated at 24V 5W, for use in side lamp and parking light circuits on 24V vehicle electrical systems. Small-wattage bulb designed for marker an...

Bulb 24V 21/5W dual-filament bulb for 24-volt electrical systems. The 21W filament serves the stop light circuit and the 5W filament serves the tai...

Drive Belt short V-profile belt for 24-volt Land Rover applications. Drives ancillary components in the engine accessory belt system.

24v dsl long belt

Roller Bearing for use in drivetrain and mechanical assemblies.

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Sealing Washer for the coolant temperature transmitter adaptor, for use on the 2.25L Diesel, 2.5L Diesel, and 2.5L Turbo Diesel engines. Fitted at...

Sediment Retainer for the fuel lift pump glass sediment bowl - the clamp that secures the glass bowl to the underside of the pump. It holds the bo...

Strap

Clutch Fork for the clutch actuation assembly in the gearbox bellhousing. This fork pivots on a fulcrum post within the bellhousing and translates...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 3-1/4" shank length. This long-shank bolt is used at the alternator mounting on...

Sealing Washer for diesel fuel injectors, positioned at the injector nozzle seat in the cylinder head to seal against combustion gases around the i...

Ballast Resistor Resistor in the ignition primary circuit of the 3.5L V8 petrol engine. Wired in series with the ignition coil, it drops the suppl...

Clutch Cylinder Adaptor - a pipe union that connects the hydraulic clutch supply pipe to the inlet port of the clutch master cylinder. Fitted at t...

Stop Light Switch mounts at the brake pedal and switches the rear brake (stop) lamps on when the pedal is depressed, operating within the brake-lig...

Starter Solenoid Relay for 12V petrol engines, acting as a high-current switching relay in the starting circuit. When energised by the ignition sw...

Dashboard Light Switch for Land Rover Series II, IIA, and III. This switch assembly controls the dashboard illumination circuit within the electric...

Brake Vacuum Tank for the Land Rover Series III 2.25 Diesel. Fitted in the brake servo vacuum circuit, the tank stores a vacuum reserve to ensure c...

Ball Joint - Accelerator Linkage is a mechanical pivot joint used in the accelerator linkage assembly. This ball joint connects articulating rods ...

Instrument Voltage Stabiliser - a thermal bimetallic unit mounted on the back of the instrument cluster that regulates the supply voltage to the fu...

Wiper Motor Mounting Pad for the rear wiper motor, used on the Defender and Range Rover Classic. This rubber fixing pad sits between the wiper mot...

Brake Drum Screw for the brake drum assembly. This retainer screw secures the brake drum to the wheel hub flange, preventing the drum from displac...

Braided Earth Strap with Battery Clamp - 300mm for the vehicle electrical grounding circuit. This braided copper earth strap is fitted with an int...

Braided Earth Strip is a flexible braided conductor that forms an electrical earth (ground) bond between two points in the vehicle. It provides a ...

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Alternator Bearing Kit - a service kit containing the bearing components required to recondition an alternator unit. Intended for use during alter...

Brake Servo Repair Kit for the Type 50 vacuum brake servo unit (227mm diameter). This overhaul kit contains the components necessary to rebuild th...

Valve repair kit

Lights and Heater Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for the exte...

Lights and Heater Toggle Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for t...

Tow Ball & Pin is a towing coupling component that mounts to the tow bracket or drop plate. The ball provides the coupling point onto which a ...

Nut is a hexagonal nut cut with a 7/16" BSF (British Standard Fine) thread. It threads onto a matching 7/16" BSF bolt or stud to secure a bolted j...

Speedometer Pinion Oil Seal for the gearbox speedometer drive take-off. It seals around the speedometer drive pinion where it enters the gearbox ho...

Glazing Rubber Seal for retaining glass panels in fixed window aperture frames. This flexible rubber channel seal locates in the groove of the win...

Glazing Rubber Strip - rubber glazing section supplied by the metre. It beds and seals a fixed glass panel into its body aperture, locating the gla...

Steering Relay Oil Seal for the steering relay unit, part of the steering linkage. The steering relay transfers movement from the steering box dro...

Exhaust Gasket sealing the exhaust manifold-to-downpipe flange on Series Land Rover 4-cylinder petrol and diesel engines. This four-hole flange ga...

Lock Nut for the Land Rover Series gearbox primary pinion bearing. This nut retains the front bearing on the primary pinion (input shaft), securin...

Dowel A locating dowel for the engine cylinder block and cylinder head assembly. It seats in machined bores to align the cylinder head to the bloc...