for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Manifold Absolute Pressure (MAP) Sensor for the engine management air intake system, mounted on the inlet manifold. The sensor measures absolute p...
View full detailsBlanking Plug for the cylinder block of the Td5 2.5L 5-cylinder turbo diesel engine. The plug closes a machined aperture in the cylinder block cas...
View full detailsWiper Spindle Washer for the rear screen wiper assembly. This plastic outer washer fits over the wiper spindle where it exits the body panel, seati...
View full detailsO-Ring that seals the oil cooler pipe and hose connections. It provides the seal at engine and transmission oil cooler unions, on manual and autom...
View full detailsSealing washer for a threaded fitting in the engine lubrication circuit. The washer seats under the shoulder of the fitting and is compressed as t...
View full detailsOil Cooler Housing Seal for the oil cooler and filter assembly on the Td5 2.5L five-cylinder turbo diesel engine. The seal sits at the joint betwe...
View full detailsValve Guide for the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. Pressed into the head, the guide supports the valve stem and ...
View full detailsPower Steering Pump Pulley for the Td5 2.5L five-cylinder turbo diesel engine. The pulley mounts on the power steering pump shaft and is turned by...
View full detailsWater Pump Cover for the coolant pump on the Td5 2.5L five-cylinder turbo diesel. The cover closes the coolant pump and is sealed to the pump with...
View full detailsSupport Bracket - the alternator mounting bracket for the Td5 2.5L 5-cylinder turbo diesel engine. It bolts to the engine to locate and support th...
View full detailsConnecting Rod Small-End Bush for the Td5 2.5L five-cylinder turbo diesel engine. The bush is pressed into the small end of the connecting rod and...
View full detailsExhaust Valve for the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. The valve seals the combustion chamber against the exhaust ...
View full detailsInjector Insulation Pad for the fuel injection system on the Td5 2.5L five-cylinder turbo diesel engine. The pad fits over the electronic unit inj...
View full detailsTail pipe - the final section of the exhaust system, fitting downstream of the rear silencer and carrying the exhaust gases past the rear of the ve...
View full detailsHose Bracket - a retaining clip for the heater pipe and hose. It secures the heater hose along its run, holding it in position and preventing chaf...
View full detailsPiston for the 4.0L V8 EFI petrol engine, supplied without piston rings. Reciprocates within the cylinder bore, transmitting combustion pressure t...
View full detailsPiston for the 4.0L V8 EFI petrol engine, high-compression specification. Reciprocates within the cylinder bore, transmitting combustion pressure ...
View full detailsInjector Rocker Shaft Nut for the 2.5L Td5 five-cylinder turbo diesel engine. Secures the injector rocker shaft to its pedestals on the cylinder h...
View full detailsO-Ring is a sealing ring used on the V8 EFI petrol engine. It seals an engine sensor at its mounting, maintaining a leak-tight joint.
Fuel Strainer - gauze strainer for the fuel pressure regulator in the cylinder head fuel block of the Td5 2.5L five-cylinder turbo diesel. Fuel de...
View full detailsValve Spring - V8 is a cylinder head valve spring for the Rover 3.5L and 3.9L V8 petrol engine. The valve spring seats between the cylinder head a...
View full detailsKey - Mainshaft
Turbo Oil Feed Pipe - oil supply pipe in the turbocharger lubrication circuit of the Td5 2.5L five-cylinder turbo diesel. It carries pressurised e...
View full detailsTransmission Brake Bolt for the transmission-mounted parking brake. The bolt secures a component of the transmission brake, which acts on the rear...
View full detailsH3 Halogen Bulb, 55W, single-filament. The H3 is a single-filament halogen capsule with a flying-lead connector, used in auxiliary lighting units ...
View full detailsAnti-Squeal Shim - Set of 4 is a set of self-adhesive noise-dampening shims for disc brake pads. Each shim is cut to shape and bonded to the steel...
View full detailsCylinder Head & Sump Bolt Bolt used on the cylinder head and sump of the 2.5L Td5 five-cylinder turbo diesel engine.
Bolt Mounting bolt for the oil cooler/filter and turbocharger on the 2.5L Td5 five-cylinder turbo diesel engine.
Gear Selector Bush for the LT230 transfer box high/low gear change mechanism. The bush seats in the gear change housing and carries the high/low s...
View full detailsHandbrake Shoe Kit - the retention (hold-down) hardware for the transmission handbrake, which acts on the LT230 transfer box rather than at the roa...
View full detailsEGR Blanking & Silicone Hose Kit disables the exhaust gas recirculation (EGR) function on the Td5 engine, blanking off the recirculation of exh...
View full detailsTensioner - Timing Belt
Piston Assembly for the Td5 2.5L 5-Cylinder Turbo Diesel, part of the cranktrain within the cylinder block assembly. Oversize: 0.020 in (approximat...
View full detailsAlternator Bracket for the Td5 2.5L five-cylinder turbo diesel engine. The bracket bolts to the engine block and carries the alternator, locating ...
View full detailsPiston Assembly - Eng
Piston and Pin Assembly - TD5
Transfer Box Gear Shaft carrying the high range output gear in the LT230 transfer box high/low gear train. The shaft transmits drive from the inte...
View full detailsReverse Gear - mainshaft gear in the 5th and reverse gear train of the R380 five-speed manual gearbox. The gear runs on the gearbox mainshaft and ...
View full detailsSteel Wheel - a 16 x 10 inch steel road wheel with a simulated beadlock outer ring, styled to resemble a clamped beadlock without retaining the tyr...
View full detailsLamp
Shock Absorber - 8-stage adjustable rear damper, left-hand side, with a piggyback reservoir. 52 mm zinc-plated monotube body and reservoir, pin mo...
View full detailsFuel Block Connector - fuel block and pressure regulator assembly in the fuel supply and return circuit of the Td5 2.5L 5-cylinder turbo diesel. I...
View full detailsCrown wheel and pinion set with a 4.75:1 final drive ratio for the rear differential, long nose differential configuration. Tooth count is 38 on th...
View full detailsCrown wheel and pinion set with a 4.75:1 final drive ratio for the front differential, long nose differential configuration. Tooth count is 38 on t...
View full detailsCrown wheel and pinion set with a 4.1:1 final drive ratio for the front differential, long nose differential configuration. The crown wheel and pi...
View full detailsCrown wheel and pinion set with a 3.8:1 final drive ratio, suitable for both the front and rear differential. The crown wheel and pinion form the ...
View full detailsPinion Shaft
Layshaft for the R380 five-speed manual gearbox, part of the main gear train assembly. Also referred to as the lay cluster or countershaft, the la...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →