Land Rover Discovery 2 Parts

Centrifuge Oil Drain Pipe Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. Seals the oil drain pipe at the engine's centrifugal oil cleaner...

Rear Crankshaft Oil Seal seated in the crankshaft rear oil seal housing at the back of the cylinder block, sealing the point where the crankshaft e...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Fuel Tank Breather Hose for the fuel filler and tank ventilation circuit. Connects the fuel tank to the filler neck, venting the tank so that air ...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Glow Plug

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...

O-Ring for the fluid suction pipe of the ZF four-speed automatic transmission. Seals the joint at the suction (pick-up) pipe that draws automatic ...

Layshaft Bearing for the LT77 and R380 5-speed manual gearbox fitted to the Defender, Discovery 1, Discovery 2, and Range Rover P38. The layshaft ...

O-Ring for the fuel injector harness assembly on the Td5 2.5L 5-Cylinder Turbo Diesel engine. This O-ring provides a seal within the fuel injector...

Cylinder Head Dowel - Plastic is a locating pin fitted at the mating face between the cylinder block and cylinder head in the Td5 2.5L 5-cylinder t...

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

EGR Cooler Hose - Engine to Cooler is a coolant hose serving the exhaust gas recirculation (EGR) system. It carries engine coolant from the engine...

Propshaft Gaiter (Sliding Joint) is the flexible rubber boot that seals the sliding splined joint of the propshaft in the drivetrain. The sliding ...

Crankshaft Sensor Spacer for the Land Rover Td5 2.5-litre 5-cylinder turbo diesel engine in manual transmission applications. This spacer fits bet...

O-Ring - Diff Lock - LT230 provides the hydraulic seal at the differential lock mechanism and front output shaft location within the LT230 transfer...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...

Caged Captive Nut - an M8 nut held in a spring-steel cage that clips into a panel or bracket to provide a captive threaded fixing. It anchors the ...

O-Ring is a sealing ring used within the ZF 4-speed automatic gearbox and the LT230 transfer box. This O-ring seals fluid passages or housing inte...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Needle Bearing is an internal roller bearing used within the LT77 5-speed and R380 5-speed manual gearbox assemblies. Needle roller bearings of th...

Oil Filler Cap for the engine oil filler neck. Seals the oil filler aperture in the valve cover, preventing oil vapour loss and contamination ingr...

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Connecting Rod Bolt for the Rover V8 EFI petrol engine, part of the connecting rod assembly in the engine bottom end. The bolt clamps the connecti...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Connecting Rod Bolt for the engine bottom end, clamping the big-end bearing cap to the connecting rod around the crankshaft journal. Working as a ...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Baulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...

heavy duty spring front RR/disco pair, like DA4201 and TF014.

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Crankshaft Bolt is the retaining bolt that secures the pulley and damper assembly to the nose of the crankshaft on the V8 petrol engine. Threaded ...

Exhaust Manifold for the Td5 2.5L five-cylinder turbo diesel engine. The cast manifold bolts to the exhaust ports on the cylinder head and collect...

Valve Stem Oil Seal for the Td5 2.5L five-cylinder turbo diesel engine, fitted at the top of the valve guide in the cylinder head. It seals around...

Yoke Transmission

Layshaft Bearing for the R380 five-speed manual gearbox. This taper roller bearing supports the layshaft (countershaft) within the gearbox casing, ...

Spherical Bush for the LT77 and R380 manual gearbox gearchange mechanism. It seats the spherical pivot at the base of the gear lever inside the re...

Clevis pin

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Intercooler Hose for the Td5 2.5L 5-cylinder turbo diesel, part of the charge-air system between the intercooler and the engine. It carries cooled...

Clutch Kit renews the friction components of the Td5 driveline clutch and is supplied without the release bearing. The kit comprises the clutch co...

Fuel Tank Sender Wrench is a special service tool for the fuel tank sender unit assembly. It engages the metal locking ring that retains the fuel ...