Land Rover Discovery 2 Parts

HT Ignition Lead - No.7 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Bow Shackle Bow-shaped recovery shackle with a threaded pin, used to connect a recovery strap or rope to a recovery point on a winch bumper. The w...

Camshaft for the valvetrain of the 4.0/4.6L V8 petrol engine. Mounted in the cylinder block and driven from the crankshaft, the camshaft lobes act...

HT Ignition Lead - No.6 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

HT Ignition Lead - No.5 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

Front Driveshaft Oil Seal located at the differential housing output in the Front Axle Assembly, sealing around the front halfshaft where it exits ...

HT Ignition Lead - No.2 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

Exhaust Manifold Gasket for the 4.0L and 4.6L EFi V8 petrol engine. This twin-port gasket seals the exhaust manifold-to-cylinder head joint at two...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Grommet is a sealing grommet fitted to the engine oil sump on V8 petrol engines. It seals the point where a tube or fitting passes through the sum...

Air Flow Sensor - V8 is the mass air flow (MAF) sensor for the V8 EFI petrol engine, forming part of the air cleaner and intake assembly. Mounted ...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Air Flow Sensor - V8 is the mass air flow (MAF) sensor for the V8 EFI petrol engine, forming part of the air cleaner and intake assembly. Mounted ...

Viscous Unit

Layshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...

Oil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...

Brake Pad Set for the front axle disc brake assembly. The pads locate within the front calipers and clamp against the vented front discs, generatin...

Coolant Expansion Tank Cap rated at 1.4 bar, fitted to the expansion (header) tank of the engine cooling system. The cap seals the expansion tank ...

Air Flow Sensor - V8 is the mass air flow (MAF) sensor for the V8 EFI petrol engine, forming part of the air cleaner and intake assembly. Mounted ...

HT Ignition Lead - V8 - No.8 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition out...

Rear Brake Pad Set for the rear disc brakes, supplied as an axle set covering both rear wheels. The friction pads are clamped against the rear bra...

Idler Pulley - a smooth-faced guide pulley in the V8 auxiliary (serpentine) drive belt system. Mounted on a fixed pivot, it routes the accessory d...

HT Ignition Lead - No.4 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

Rocker Cover Gasket for the Rover V8 petrol engine, sealing the rocker (valve) cover to the cylinder head. The gasket seats between the cover flan...

Oxygen (Lambda) Sensor for the rear, post-catalyst position in the exhaust system. Mounted in the downpipe downstream of the catalytic converter, ...

Handbrake Shoe Set for the transmission handbrake. Part of the transfer-box-mounted drum parking brake. The shoes expand against the inside of the...

Automatic Gearbox Sump Plug - the threaded plug that seals the drain point on the ZF automatic transmission oil pan. Removed to drain the transmis...

Panhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...

Panhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...

Coolant Expansion Tank Cap rated at 1.4 bar, fitted to the expansion (header) tank of the engine cooling system. The cap seals the expansion tank ...

Hex Nut, M24 x 1.5mm securing the constant-velocity (CV) joint stub shaft to the wheel hub within the driveline. The nut retains the CV joint and ...

Brake Light Switch, the stop lamp switch mounted at the brake pedal. When the brake pedal is depressed the switch closes the stop lamp circuit to ...

Sump Gasket for the Rover V8 4.0 and 4.6 petrol engine, sealing the oil sump to the underside of the cylinder block. This is the one-piece rubber-...

Head Set 4.0/4.6 with Bolts - V8

Water Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...

Taper Roller Bearing - shaft bearing for the R380 five-speed manual gearbox. A taper roller bearing carries both radial load and axial thrust, loc...

Camshaft for the Rover V8 EFI petrol engine (3.9L, 4.0L and 4.6L variants). Mounted centrally in the cylinder block, the camshaft is driven from t...

Plain Washer is an M12 plain washer used at the rear propshaft flange fixing. It seats under the bolt head or nut at the propshaft flange, spreadi...

Polyurethane Ball Joint Boots for the front axle upper and lower ball joints. These flexible boots seal over the ball joint to retain grease and ke...