Land Rover Axle & Swivel Parts

Swivel Pin Housing Kit rebuilds the upper pivot of the front axle swivel housing, where the steering knuckle articulates on the axle. This is the v...

Half Shaft Shim - 0.90mm is a 0.90mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Half Shaft Shim - 0.60mm is a 0.60mm selective shim used to set the endfloat of the axle half shaft within the hub assembly. It is fitted at the d...

Front Axle Shim, 0.45mm thick. Fitted to the front axle half-shaft assembly to set the correct end-float, taking up clearance so the shaft is posit...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Shim is a 0.002" adjustment shim for the manual (non-power-assisted) steering box. It is fitted within the steering box to set the correct end-flo...

Door Glass Regulator Shim - a packing shim used at the door window regulator and glass channel. It sets the regulator and channel at the correct st...

Stub Axle - rear stub axle carrying the hub and bearings at the rear axle. Bolted to the rear axle casing, it forms the fixed spindle on which the...

Body Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...

Half Shaft for the axle drive assembly, transmitting drive torque from the differential to the wheel hub. Splined to the differential side gear at ...

Front Axle Shaft - left-hand - for the Defender with early-type 23-spline CV joint. This drive shaft transmits torque from the front differential ...

Swivel Repair Kit - a service kit for the front axle swivel housing on the early Defender front axle. The swivel housing forms the sealed ball joi...

Swivel Housing: - Classic Defender 90/110/127/130 upto KA930455 (upto and including 1993 modelyear) (NON-ABS) Axle Code 20L, 21L, 22L, 23L, - Disco...

Stub axle

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Swivel Pin is the upper pin of the front axle swivel assembly. It bolts to the top of the swivel housing and carries the upper bearing about which ...

Trunnion

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Swivel Pin Kit for the upper front axle swivel on ABS applications, serving the top swivel pin that forms the upper pivot between the swivel housin...

Outer Shim - 1.35mm - Front Halfshaft / CV Joint This 1.35mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

Front Half Shaft for the right-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant vel...

Half Shaft is the left-hand rear axle half shaft. Operating within the rear axle assembly, it transmits drive torque from the rear differential to...

Rear Half Shaft - right-hand - for the Defender with early-type 23-spline CV joint. This solid steel drive shaft transfers torque from the rear di...

Upper Front Swivel Pin for the front axle swivel housing assembly. The upper swivel pin bolts to the top of the swivel housing and forms the upper...

Rear Stub Axle for the Salisbury rear axle assembly. The stub axle bolts to the outer end of the axle casing and forms the fixed spindle on which ...

Outer Shim - 1.65mm - Front Halfshaft / CV Joint This 1.65mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Axle Flange Kit for the pinion drive flange of the Salisbury rear differential. The flange transmits drive from the differential pinion to the rea...

Axle Casing Stud for the front and rear axle case assemblies. It is a threaded stud used to secure components to the axle casing on the Land Rover...

Drive Flange Bolt secures the drive flange to the wheel hub on the axle. Supplied as a set of 10. These bolts are used with the DA1148 and DA1149 ...

Drive Flange Nut - replacement centre nut for the heavy-duty thin-type drive flange, black finish. The drive flange sits at the outer end of the f...

Front flange LT230

Swivel Ball Taper Plug for the front axle swivel housing. This tapered-thread plug screws into a port in the swivel ball housing, sealing it agains...

Rear Axle Breather Pipe vents the rear axle casing. It equalises internal air pressure as the axle heats and cools, allowing the casing to breathe...

Rear Axle Outer Stub Shaft is part of the rear axle and hub assembly on the left-hand (LH) side. It transmits drive from the rear halfshaft to the...

Swivel Housing Repair Kit for the front axle swivel assembly, non-ABS specification. Supplied for one side. The swivel housing sits at the outer e...

Swivel Housing Gaiter Kit - Leather - Pair for the front axle swivel housing assembly on the Defender 90 and 110. The swivel housing gaiter seals ...

Half Shaft Shim is a 1.50mm selective shim used in the axle drive shaft and hub assembly. It sets the endfloat of the half shaft drive member with...

Shim

Primary Pinion Bearing Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox casing. 2.05 mm thick, it control...

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Front Half Shaft for the left-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant velo...

Differential Pinion Bearing Shim - 0.068 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Differential Pinion Bearing Shim - 0.066 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Differential Pinion Bearing Shim - 0.064 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Shaft 90/110 RH 31/10

Rear Left-Hand Half Shaft for the 10/24 spline rear axle. The half shaft transmits drive from the differential to the rear wheel hub. This left-ha...

Rear Axle Half Shaft - right-hand, 10/24 spline, for the Series III rear axle. This shaft transmits drive from the rear differential to the rear wh...