Land Rover Defender Parts

Ceramic Glow Plug - cold-start heating element from the diesel pre-heat system, threaded into the cylinder head with the tip projecting into the co...

Timing Chain Guide, Lower Primary from the front timing gear assembly. It bears against the primary drive chain on the run between the crankshaft ...

Exhaust Clamp for the 2.0L Ingenium diesel exhaust system (AJ200D / AJ20D4). The clamp secures the front section joint of the exhaust, holding the...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Timing Cover Blanking Plug - threaded plug that closes an aperture in the front timing cover of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4, al...

Timing Gear Bolt - special-form fastener used in the timing drive assembly at the front of the Ingenium petrol engine. It is one of the fixings th...

Timing Chain Tensioner Arm is the pivoting guide arm in the timing drive of the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4 / AJ200P ...

Cylinder Head Bolt for Ingenium petrol engines (1.5L AJ20P3, 2.0L AJ200 / AJ20P4, 3.0L AJ20P6 / AJ22P6). The bolt clamps the cylinder head to the ...

EGR Inlet Gasket for the 2.0L AJ200 Ingenium diesel Exhaust Gas Recirculation system. Seals the inlet joint of the EGR assembly to maintain a gas-...

Cylinder Head Gasket for the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4). The gasket seals the joint between the cylinder head and ...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Timing Gear Bolt - a fixing bolt in the engine timing drive, retaining a timing gear. It secures the timing gear on the 2.0L four-cylinder AJ200 p...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Guide - Timing Chain

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

O-Ring is a 60mm sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder diesel engine (AJ200 / AJ20D4 family). ...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

TMAP Sensor is the combined intake air temperature and manifold absolute pressure sensor, fitted to the inlet manifold and intercooler ducting. It...

MAP Sensor is the manifold absolute pressure and charge-air temperature sensor mounted in the inlet manifold. It reports intake manifold pressure ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Rear Crankshaft Oil Seal for the 2.0L AJ200 engine. This seal fits around the rear of the crankshaft where it exits the cylinder block, retaining ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit, 60mm. This seal maintains a gas-tight joint within the EGR section, sealing the connection...

Bearing Cap Bolt with hex head for the crankshaft main bearing assembly of the AJ200 / AJ20 four-cylinder Ingenium engines. Secures the crankshaft...

Exhaust Gas Recirculation Gasket seals the exhaust gas recirculation (EGR) connection on the left-hand side, maintaining a gas-tight joint within t...

Gasket - Exhaust Manifold

Adhesive and Sealer is a glass bonding adhesive and sealer used to seat and seal fixed automotive glazing to the body. It bonds and seals the wind...

Intake Manifold Gasket seals the joint between the intake manifold and the cylinder head, within the air intake assembly. It maintains an airtight...

Intake Manifold Gasket seals the joint between the intake manifold and the cylinder head, within the air intake assembly. It maintains an airtight...

O-Ring for the oil filter and cooler assembly. It seals a connection within the oil cooler and filter assembly, maintaining oil-tight integrity at...

Seal for the oil filter to oil cooler connection, part of the oil cooler and filter assembly. This O-ring seals the joint between the oil filter h...

Inlet Valve is a poppet valve in the cylinder head of the 2.0L Ingenium diesel engine (AJ200D / AJ20D4 / AJ21D4). Seated in the intake port, it op...

Sealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...

Upper Timing Cover Gasket seals the upper timing chain cover to the cylinder head on the 2.0L Ingenium diesel engine (AJ200D / AJ20D4). It forms t...

Camshaft Cover Gasket sealing the camshaft cover to the cylinder head. It seals the joint between the camshaft (cylinder head) cover and the cylin...

Sealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...

Cover Gasket for the upper timing chain cover. It seals the joint between the upper timing chain cover and the engine, maintaining an oil-tight se...

Camshaft Cover Gasket sealing the camshaft cover to the cylinder head. It seals the joint between the camshaft (cylinder head) cover and the cylin...

Exhaust Valve is a poppet valve in the cylinder head of the 2.0L Ingenium diesel engine (AJ200D / AJ20D4 / AJ21D4). Seated in the exhaust port, it...

Valve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...

Timing Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...

Timing Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...

Timing Chain Tensioner Arm for the engine timing gear. It bears against the timing chain and transmits the tensioner load to take up slack and mai...

Valve Rocker Arm for the cylinder head valvetrain. It transfers camshaft lift to the valve, actuating the valve as the camshaft rotates. Fitted to...